Visit Talon Tunes

Updated on January 12, 2008

walkonking

Participant

January 12, 2008 at 4:20 am

Hey ROB Guess what these are!

General Chat

All Replies

Viewing 15 replies - 1 through 15 (of 31 total)

1 2 3 →

rob3dr

Participant

January 22, 2008 at 5:54 pm

At work now so I cannot view pics, but I gotta see these hands everyone is raving about……..

saugus18

Participant

January 22, 2008 at 4:46 pm

Nice work for sure… you’re left hand is kinda… well…. nice to….. 😆

shadoh

Participant

January 22, 2008 at 4:42 pm

Who’s the model?

volsr1

Participant

January 22, 2008 at 3:08 pm

That’s fantastic work! Is there a drooling emoticon?

j3magnum

Participant

January 22, 2008 at 1:34 pm

Ughhhhh,,,Rob lives at my house now….LOL…DOn’t forget me the next time you make some….

rob3dr

Participant

January 22, 2008 at 1:20 pm

Will do!!!!!

walkonking

Participant

January 22, 2008 at 6:27 am

Okay Rob it is done. I picked up some hose clamps and sprayed them flat black. I put another coat on the butt piece also.

Did you find your butt plate yet? I can make one for it if you need but it will take me a few days to get to it.

You should PM me with your address and send me your first born 😆

j3magnum

Participant

January 20, 2008 at 3:00 pm

Looks Good Adam,,,,,,I need a mill,,,I need a mill,,,I need more guns,,, I ned,,I need,, I need,,,,,,,To find a new Hobby before my wife shoots me

walkonking

Participant

January 20, 2008 at 6:00 am

The lazy way is to put the hose clamps over the tank cover and paint them black. But the correct way is this.

Put your tank on your gun and determine where the butt piece will go. Put the hose clamps on your butt piece and see where the straps for the clamps will intersect with the tank. That is the area you want to slice with a box cutter. You can make slits or you can cut out a rectangular area for the butt pad. I do recommend leaving rubber at the butt of the tank for the butt piece to rest on. This will allow for a compressive factor when tightening the butt piece down. If you can just make slits for the hose clamp to go through then you will be set. The rubber cover is tough stuff and will require careful cutting with a box cutter. I remove the tank cover with an air compressor. Just blow air in the hole at the back and it will lift off like a rocket. You can install it the same way but push down.

If you look at my set up you will see I cut the tank cover to much. But first timea and all.

It is tricky but I will walk you through it.

rob3dr

Participant

January 20, 2008 at 5:03 am

Was looking at your original post and trying to figure it out. Looks like the tank cover must be peeled off somehow.

Did I mention I’m excited! ❗

walkonking

Participant

January 20, 2008 at 5:00 am

I will include the hose clamps used to connect it. I will have to tell you how to get it on later.

rob3dr

Participant

January 20, 2008 at 4:42 am

Hose clamps! Found it!

WOO-HOO!

rob3dr

Participant

January 20, 2008 at 4:38 am

DAMN thats pretty!!! REALLY looks sharp! I gotta dig out my old buttpad now…. I know I gave one away to someone. I’ll have to search around and find the other if I still have it. If not, I’ll be posting a wanted post..haha

Remind me again how that connects to the tank? 😳

walkonking

Participant

January 20, 2008 at 4:34 am

Here are some picts. I hope you like it. It is primered and painted and when it chips or get scratched you can hit it with flat black paint for touch up.

I am giving it another coat and will get it sent out next week.

This pict has my but plate on it for demo purposes.