stealth
hi still having probs with this gun im just about to saw it in half I put new breech seals in and still no good the grouping at 17 yrds is crap to say the least
I have striped it down to show you whats in there to see if its right
the shots were aimed at the center hole and kept aiming at the same hole
All Replies
Viewing 15 replies - 1 through 15 (of 15 total)
finaly got my chrono working so I tried it with 180bar in the stealth this is what it showed 10.68 .10.65 .10.70 11.56 12.40
then filled to 200 bar and it went 10.40 10.80 .967
it hasent got a power wheel so uk spec gona try some different pellets through it the guy said it had lupy parts in it not sure what
Those barrel bushings don’t look like stock ones..at least they don’t look like mine. They are far wider.
Where is your power wheel? Unless this is one of those tricked out guns..shooting big bore bullets..You should have a power wheel.
No power wheel means your spring is way 2 whimpy. the power occupies about 2″ , thus putting more tension on the spring.
No power wheel on UK spec’ guns.
There is something awry..
Those barrel bushings don’t look like stock ones..at least they don’t look like mine. They are far wider.
Where is your power wheel? Unless this is one of those tricked out guns..shooting big bore bullets..You should have a power wheel.
No power wheel means your spring is way 2 whimpy. the power occupies about 2″ , thus putting more tension on the spring.
Use a cotton bud to check the muzzle, if it snags as you pull it out then it’ll need some tlc.
just put the hammers in the other way no joy the grub screws are snug I put grease on the top hat made sure the frame clean im at a loss there doesent seem to be a crown on the barrel just flat doesent seem to have been cut is any body in the uk that can sort this gun out still feel like chopping it up lol
Hammer is the wrong way round(putting it round the other way will make for better trigger release) Breech will only work one way round so that must be right. Make sure you snug up the grubs onto those barrel bushings, that’s probably the main culprit. Better still get them replaced. Put some silicone grease on the o rings inside the breech. Clean the inside of the frame where the hammer rides, no lube or anything, just a damn good polish, same for the hammer. And I reckon you could do with a spacer or two to preload that spring a bit. Make sure the grubs on the top hat are secure otherwise the tophat will be moving about. If you have the valve with the oring where the stem goes pull the stem out put some silicone grease on that as well. Don’t fill more than 2400psi to start with. See if that tightens things up, though to be honest at 17 yards even wildly swinging fps wouldn’t cause that crap a grouping. I’ll wager it’s the bushings, try and get them smoothed out. Test without any silencer or end cap, could be clipping which is also a very likely. Give the barrel a pull through if you haven’t already. Probably not the cause as they don’t ever really need a clean..
Oh, and fix your crony, it’s an essential bit of kit.
im in the west mids
have I got the hammers the right way round or dosent it matter
were do I set the top hat from and how much the power I cant check chrono busted but its doesent seem over powerd it wont go through a pice of chipboard and most my other guns do
im in the uk i swoped this for a air arms s 400 that was pellet on pellet the bloke said hes polished it and it shoots mint this is how it was when I got home as it was late I dident shoot it at his house I will never do it again
See how it slugs thru the barrel, make sure barrel is clean and check your crown and end cap.
As per Pablo, looks pretty chewed up 😯 tophat is way out too 😯
Holy crap, who’s dog has been chewing the parts?? What power are you shooting at?
Where abouts are you?
Viewing 15 replies - 1 through 15 (of 15 total)
- You must be logged in to reply to this topic.
Pull the stem out and take a couple photos. I suspect it’s been drilled out a bit.