Need Colibri O ring sizes, please,..
Need to know the sizes of the three regulator o rings, specifically,…. however If anyone has a complete chart or even just the sizes of the Colibri’s o rings, could you please either post it here or email it to me? I’m bored, It’s pouring rain and I want to service an HB reg…
Many thanks
218bee
All Replies
sweet info…thanks guys
I found a set of orings for mine on eBay. I’d looooove a better version of that diagram too! Please.
Did anyone ever find a better copy of the breakdown for the hummingbird? If so could i please get a copy, i am going to undertake a complete rebuild front to back and add some mods as well.
Thanks in advance.
I found the image on a foreign airgun message board either czech or Russian. It was just before Xmas and I have tried to find it since (at the time I didn’t have a Colibri but saved it as I’d not come across one before) Its not as Hi Res as the Cricket version thats available on a French website and I’ve not seen it since (or a higher quality version) Its good enough to put the gun back together and most of the text is readable to an extent.Hey its better than nothing and thats why I posted it.
Manny thanks.
3×1.5
Do you know the O ring size for the fill prob of the hummingbird? I didn’t see it listed in there and where did you find the drawing? i would love to print one out for working on my gun?
Manny thanks.
Regards
218bee
I would also appreciate one as well
ksfastman@cox.net
Great stuff, Larry. This is just what I was after… Should you find a better resolution version can you please email it to me as well?
Regards
218bee
Hope it helps
Dave, I Emailed you a printable 300dpi…hope this helps.
I will try to find a better quality schematic.
Larry
I wish it was higher resolution (if anyone has it at higher res please post it)
Hope it helps
Awesome info, Greg….although looks like I have to translate some of it….Some of those are oddball sized o rings for sure and I had to round up on some of them…better too fat than too skinny when it comes to Orings. By any chance, have you got a photo-schematic , like what’s available for the Cricket?
I have one Colibri that’s got a very slow leak ( like 10 BAR in a few days) but I just freshened up all the Orings on her I could easily get to ( air tube, air gauge, and regulator) so hopefully She’s good to go…Even put in the slightly oversized Orings on the reg housing & valve inspection port like Ernest suggested….Charged her to 200 BAR last night so time will tell..
Really don’t want to submerge it, but that’s the next step if it still leaks..
Thanks again for this info.. :8: :8:
Here you go Bee,
Colibri O-rings
2.8 x 1.6-1 PCs (charging port)
2.8 x 1.9-2 PCs (kapilârka)
3.5 x 1.5-3 units (gear-piston fitting the filling)
5 x 1.5-1 PCs (pressure reducer (nozzle))
5.5 x 1.5-1 PCs (normal seal dosylatelâ 5.5)
5.7 x 1.9-1 piece (seal of tubular dosylatelâ 5.5)
4.5 x 1.5-1 PCs (normal seal dosylatelâ 4.5)
4.6 x 1.9-1 piece (seal of tubular dosylatelâ 4.5)
6 x 2-1 PCs (gear (plunger))
8 x 1-1 piece (reducer (nozzles))
10 x 2-1 PCs (pressure gauge)
13 x 2.5-2 PCs (reducer, NAC.)
22 x 2-2 piece (moderator)
30 x 3-2 pieces (front and rear tank tube)
~ Greg
Texted him,….got no reply and didn’t want to bug him further…took it apart and found what I needed to know. No biggie..
Thanks Greg,.
- You must be logged in to reply to this topic.
Hope it helps
Dave, I Emailed you a printable 300dpi…hope this helps.
I will try to find a better quality schematic.
Larry
Hi Larry , may i have a higher resolution Colibri schematic ? Email : koimai@gmail.com
Thanks