10 shot mag for the stealth
😯 😀 ok LADS MY MATE IS A WELL KNOWN GUNSMITH ANS HAS BEEN WORKING ON A 10 SHOT MAGAZINE FOR THE STELATH.
HE,S DONE IT 😎 NOW THAY WILL BE THE BEST GUNS FOR SURE.
HE,S TRYING TO PATINT IT SO IT CARNT BE COPIED .THIS ISENT BULLSHIT IV JUST GOT OF THE PHONE WITH HIM ,,THER TESTING IT FOF ACCURCY ALL I COULD GET OUT OF HIM WAS IT RUNS ON BERRINGS??
IM GONNA DRIVE DOWN AND SEE IT SOON WHEN I PICK UP SOME HAND MADE GOODIE,S FOR MY STEALTH…
HAPPY DAYS AHEAD FOR US NOW BOYZ..
All Replies
The only way a rotating mag would work is it would have to swing pivot inline with the barrel then push pellet into barrel, swing away to fire.
Then swing magzine inline again, rotate and push pellet into barrel.
Just look at the design and you will see what I mean.
Probably faster to just load a one pellet at a time.
😉
I hope he’s alright.
He sure had a high speed run at us.
Maybe he got caught trying to take a picture of that pellet feeder?
Perhaps it was the same gunsmith who did those grips for him 😉
So, looking over the first post, who is this well known gunsmith???
Dave
That ain’t what you said last night sweety 🙂
My Jet-pack is used for noble purposes only I’ll have you know.
LOOOOOOOL 🙂
No reply from the original poster, maybe AF got wind of his claims and hired Pab to burn it to ashes with his jet pack 😀
Dave
information is true. would be mother’s pearly gate ter ‘ave a photo or even
better, ter ‘ave a video of the bloody magazine….
Gawden Bennet mate, ‘ave you gawn all cockney like?!!
You must be ‘avin some kind af giraffe!!
Al stick me gregory out ‘ere and say it aint gonna bleedin’ ‘appen….
Well, at least until me mince pies ‘ave seen it…..
ahhhh yeah, but, me China Plate of bovine retreat, Cockney is the bleedin’
language of the bloomin’ knowledgeable few. I am laughin’ loudly. your dickie
birds Highland Flin’ the bloody Hair Gel of truf I say… I fin’ it will be a long
nickle and dime until we clock the abili-y ter load a stealf wif a cornucopia
of projectiles…. 😆
information is true. would be mother’s pearly gate ter ‘ave a photo or even
better, ter ‘ave a video of the bloody magazine….
Gawden Bennet mate, ‘ave you gawn all cockney like?!!
You must be ‘avin some kind af giraffe!!
Al stick me gregory out ‘ere and say it aint gonna bleedin’ ‘appen….
Well, at least until me mince pies ‘ave seen it…..
Looks loike someone is garn ter be very busy makin’ stealf parts if that
information is true. would be mother’s pearly gate ter ‘ave a photo or even
better, ter ‘ave a video of the bloody magazine….
I though I have read some posts saying, Airforce also working on the multishot mag, is that true?
Well, I’ll believe it when I see it 😆
Jesus, he will be a millionaire soon. I could use a new car????
I am so on board for a 10 shot mag but like the rest I’ve gotta see it to believe it… 🙄
I’ve heard of shooting fishing weights but what kind of accuracy can you get out of BERRINGS??
Just pulling your chain 😈
iPhone’s got a secret snapshot app 💡
But, that all sounds to good to be true 😥
:4: :4: :4: :4:
- You must be logged in to reply to this topic.
Could be a 2 part breech. The bottom section fully in place around the barrel and the Top Hat. The cocking know doesn’t have to move the breech, just the hammer while it is also moving the pellet forward into the seated position in the barrel. So I see it as a 2 step operation of #1, rotate the cylinder to place an pellet in line with the barrel and #2, cock the hammer that also pushed the pellet forward into the barrel and when fired will of course drive the breech that is already in contact with the Top Hat/Valve to the rear for valve opening and wallah! PROBLEM SOLVED!
This leaves one last minor engineering hurdle that is to open a path around the cocking extention that pushes the pellet into the breech so it will allow the HPA to get by with the least turbulence.
BOW…BOW…THANK YOU ALL ❗ …BOW…BOW
So, tear me down,
I’m in need of a rebuild
:banghead: