good idea or no?????

At least your starting with a Condor and not doing what I did. Got a TalonSs and preceded to get the Condor stuff to fill in the blanks. Costs twice as much and it’s just stock stuff. 😡 You’d spend some $$ but you’d have a tuned Condor!

I have a TalonDor for the price of a TT tuned Condor.

See all those other airguns you have listed at the bottom of your post – just sell them – you really won’t need them.
I had Crosman NP XL 1100, 2200B and 2210SB, 9mm CX 4 Storm, 22 Mag bolt action. Sold the whole lot and ammo – ahhhhhhhh more space less stress – no micro printng – no registration.

:6:

Vendor Cost Quantity Price Description
Crosman $140.00 1 $140.00 CenterPoint 4-16 x 40 Adventure Class Scope
KitteryTradingPost.com $617.50 1 $617.50 AirForce Condor – .25 caliber – 24″ barrel
KitteryTradingPost.com $15.50 1 $15.50 AirForce Protective Tank Cap
KitteryTradingPost.com $69.00 1 $69.00 AirForce Bipod
KitteryTradingPost.com $199.95 1 $199.95 AirForce Hand Pump
PyramidAir.com $21.00 1 $21.00 AirForce Sling Swivels
PyramidAir.com $29.00 0 $- AirForce Tri Rail
PyramidAir.com $7.00 2 $14.00 EunJun 35.8 gr Pellets
PyramidAir.com $6.00 2 $12.00 EunJun 43.2 gr Pellets
PyramidAir.com $10.50 1 $10.50 Pellet Holder
PyramidAir.com $120.00 1 $120.00 Chronograph – 306796
Midwayusa.com $25.00 1 $25.00 GunGuard 36″ case – 863014
Midwayusa.com $37.00 1 $37.00 Powder Scale – 175512
Bill Leavell $58.00 1 $58.00 Frame Extender Shroud
Subssonic $30.00 1 $30.00 SubSonnic Bolt Handle
WOK $63.00 1 $63.00 Spartan Strap-On WokButt
Tony Annuzzi $75.00 1 $75.00 95 gram Hammer
Tony Annuzzi $- 1 $- Breech slide 90 durometer O-rings
Doug Noble $60.00 0 $- E-TaC- Reg
JDSAirman.com $75.00 0 $- Regulator
JDSAirman.com $70.00 0 $- 43 cu in Stubby Bottle

Total $1,728.45 $1,507.45

Tony vents the frame under the forearm with one hole, smaller than 1/8″ between the front and rear bushings. Very effective combined with the vented bushing.

Can someone explain the process or show pictures of “Frame Venting” vs. Bushing Venting (I’ve seen pictures on Tony’s site about barrel Bushing venting) on a Condor ?

I don’t know if Tony does frame venting… Good question. He does do bushing venting though, but I don’t think it’s part of a tune, I could be wrong about that, best to get in touch with him and inquire.

He should be back from vacation (I believe he was out last week), he has always been prompt in returning my phone calls, pms or emails. 😀

There isn’t much more to do…! 😉

I made my own stock for my Talon SS. R&L sells a mass produced one. If your looking to keep the rifle as a take down item the full stock makes that not possible.

There is venting the front barrel bushing to work with the shroud… Oh and a frame hole modification to work with the vented bushings.

There is a trigger modification but you may have to do that yourself, I’m not sure anyone is doing it as a service.

Both the frame mod and the trigger mod are in the Quick Reference section I think.

After all that you’ll have to shoot the shit out of it!! 😆

Do you have a chrony?