John Hagans HST tool
Well I contacted John and he made me a HST tool for my new Vulcan. No since in screwing it up using needle nose pliers or two screws or a c-clip tool.
Only took less than a week to get, Thanks John!!
All Replies
So you have the newer v2 version with new bolt, LDC and HST? Anyone have a timeline as to when the v1 and v2 were made?
You can order any and all the updates from AGN – and surely thru Anthony as well. I had a speziale load handle made to mine and Evgeny send me a new Mk2 load handle as well. He also send me a HST adjuster free of charge.
Hammer adjuster? you referring to hammer spring? Or is there a throw as well like the marauder and prod?
At least my involuntarily wait will land me with a few minor improvments… all I can do is read tales of Vulcan owners both near and far…ogle over the pictures…and dream of my own… huh kinda like pussy.
Do the following : Wash your mitts. Let them air dry. Once dry grab a piece of 240 grit sandpaper. Roll it around your thumb and index finger. Try again.
He has one shoved his ass as well.
I bet Lead can find it…
A hex key smeared with Cod oil is a slippery little bugger.
I have that hex key jammed way up my corn hole now I can’t find it. :banghead:
Exactly ! And i got scared and dropped the hex key in the Sea. Would it have been that butt plug with a key ring that would not have happened. I learned a valuable lesson that day :
A hex key smeared with Cod oil is a slippery little bugger.
:hoot:
If you syphilitic mouth-breathers would spend more time studying the facts on this forum, and less time smelling your fingers….and each other’s butts, you would note that a hex wrench is easily lost, but a genuine HST adjustment tool, with a dandy ring on the end, can be hung around your neck, and easily carried with you, should the need arise.
Besides, when was the last time you pulled a hex wrench out of your pocket to show off to your friends? Oh never mind…knowing you morons, it was probably yesterday!
When Ville showed off the hex wrench to his brother-in-law, the one interned in the Swedish Institute for Cod Oil addiction, the guy jumped back and screamed…”Drop that thing, Vil, you don’t know nothing ’bout ‘chinery!!
Hoot:
So you have the newer v2 version with new bolt, LDC and HST? Anyone have a timeline as to when the v1 and v2 were made?
You can order any and all the updates from AGN – and surely thru Anthony as well. I had a speziale load handle made to mine and Evgeny send me a new Mk2 load handle as well. He also send me a HST adjuster free of charge.
Wrong….Butt-Breath!!!
Kind regards,
Hoot:
FINALLY ! Oh, finally he´s come to his senses. That doesn´t say much but anyway. Kudos to Uncle for his choice for a really fine BP ! Fuck Ed and the elusive Lelya, i say. Fuck him and fuck his products too.
So you have the newer v2 version with new bolt, LDC and HST? Anyone have a timeline as to when the v1 and v2 were made?
It’s Hoots new finger fucker……it’s the only thing he can get up!!!
That is way better
On the latest version of the Vulcan there’s no need for a special tool. All you need is a hex key.
Why is not better make a new piece of knob like in the cricket? This is necessary still carry with the gun….
- You must be logged in to reply to this topic.
You can order any and all the updates from AGN – and surely thru Anthony as well. I had a speziale load handle made to mine and Evgeny send me a new Mk2 load handle as well. He also send me a HST adjuster free of charge.
Hammer adjuster? you referring to hammer spring? Or is there a throw as well like the marauder and prod?
At least my involuntarily wait will land me with a few minor improvments… all I can do is read tales of Vulcan owners both near and far…ogle over the pictures…and dream of my own… huh kinda like pussy.
No. I refer to HST ADJUSTER. The thingie you adjust the HST with. Regarding the Pussy : I can’t help you. It has always come easy to me since i’m handsome as hell !