O-ring sizes
Does anyone have a list of o-ring sizes for the Mutant?
*Updated thanks to Dman here is the list:
21 X 3 Seal rear / front stopper tank 1 each and Regulator OD x2
13.5 X 2 Seal valve body
12.5 x 2 Seal the barrel on the receiver.
4.47 x 1.78, -008. (.177) / 5.28 x 1.78. -009. (.22) probe seal X2
9.25 x 1.78. -012. pressure gauge
4.47 x 1.78. -008. filling nozzle .
23 x 1.5 (.177) / 1.5 x 24 (.22) magazine od x2
Regulator.
2.9 x 1.78. -006. Nozzle gear
12.42 x 1.78. -014. sleave.
6.07 x 1.78. -010. Piston reducer *Buno 70 polyurethane*
2.9 x 1.78. -006. Piston reducer. *Buno 70 polyurethane*
All Replies
Are they cheaper shipping? 🙂
Those of u interested in all meter sizes equivalents most can be found here ……..
~ Greg
The ones in the gun out of the box are like a 90d… I’ve got the best performance and reliability out of the 70d eurothane ones…
The nitrile ones I don’t feel will hold up to the cyclING of the regulator
Definitely could have been cheaper if they stuff it in a small flat rate box. These o-rings don’t take that much space. Unless they’re sending me a catelog along with them.
Donny…
Your miss understanding… I know you ordered everything in 70d…
The 2 Orings on the Regulator shaft. Should be eurothane, Not Nitrile The Eurothane Orings are for areas where you have constant abrasive movement.
With the cycling the normal 70d Nitrile just wont hold up and will break down.
Here is the Russian O-ring list translated by google and I.
NBR70
21 x 3 Seal the back/front of the tank and plugs gear //\ \ Air Tube
13.5 x 2 Seal valve body on the back of the tank tube //\ \ Main Valve to Receiver
12.5 x 2 Seal the barrel of the receiver //\ \ Barrel receiver O-ring
4.47 x 1.78 (-008) / 5.28 x 1.78 (-009) The seal on the barrel breech //\ \ .177 & .22 Breech O-rings
9.25 x 1.78 (-012) Seal the pressure gauge on the front of the tank tube
4.47 x 1.78 (-008) Seal the filling nozzle
23 x 1.5 / 24 x 1.5 Crimp ring at the store //\ \ snap rings for Main Valve & Mod ?
2.9 x 1.78 (-006) nozzle gear //\ \ Fill O-ring ??
6.07 x 1.78 (-010) The piston gear //\ \ Reg. piston larger
2.9 x 1.78 (-006) The piston gear //\ \ Reg. piston small
12.42 x 1.78 (-014) Reg. piston end cap //\ \ low psi side
Yeah I ordered everything D70.
The ones in the gun out of the box are like a 90d… I’ve got the best performance and reliability out of the 70d eurothane ones…
The nitrile ones I don’t feel will hold up to the cyclING of the regulator
Definitely could have been cheaper if they stuff it in a small flat rate box. These o-rings don’t take that much space. Unless they’re sending me a catelog along with them.
Did u order the regulator shaft in D70. Eurothane?
The ones in the gun out of the box are like a 90d… I’ve got the best performance and reliability out of the 70d eurothane ones…
The nitrile ones I don’t feel will hold up to the cyclING of the regulator
Thanks….
$9.45 fast shipping for a tiny envelope of rubbers?…that’s a mugging for sure… :suprisedn:
Placed my order with the oring store: Total came out to $17.62 with Priority mail shipping. Shipping cost more than the actual o-rings. If you’re not in a rush, shipping would’ve been $5 something for regular US mail. I got everything Buno 70, if I recall Ernest saying this is harder and should last longer.
Thanks – I stored that with the other oring documents. 😉
Ok I updated it with the proper dash – number after the metric one.
It’s nice cause the oring. Can be sourced from anywhere
Nice!!!!
Sweet Dman thanks!
Donny..
I have a full list.
Most of them are normal American sizes…
I just need to convert the list.
Anyhow
Here they are. Give me some time and I will add the American dash # to it later
21 X 3 Seal rear / front stopper tank 1 each and Regulator OD x2
13.5 X 2 Seal valve body
12.5 x 2 Seal the barrel on the receiver.
4.47 x 1.78, -008. (.177) / 5.28 x 1.78. -009. (.22) probe seal X2
9.25 x 1.78. -012. pressure gauge
4.47 x 1.78. -008. filling nozzle .
23 x 1.5 (.177) / 1.5 x 24 (.22) magazine od x2
Regulator.
2.9 x 1.78. -006. Nozzle gear
12.42 x 1.78. -014. sleave.
6.07 x 1.78. -010. Piston reducer *Buno 70 polyurethane*
2.9 x 1.78. -006. Piston reducer. *Buno 70 polyurethane*
- You must be logged in to reply to this topic.
I’ve had good luck with the Viton O-rings Ernest sent me in the reg. I have an assortment of all the O-rings in both materials, Viton and Buna. Cleaning out the over dose of grease and the new rings made my reg respond with a 5-7 fps ES. 😉