Visit Talon Tunes
Updated on April 11, 2008
mjohnson6565
Participant
April 11, 2008 at 6:02 pm
Q:

Rubber \ Neoprene Washer

I am having trouble locating rubber\neoporene washers locally. Are they any large parts warehouses etc you could suggest ?

Shrouds and Moderators

All Replies

Viewing 12 replies - 1 through 12 (of 12 total)

sotxguy
Participant
May 18, 2008 at 2:58 am

1″ tube 1/16″ wall. Ace, TrueValue, Home Depot, Lowe’s etc

savagesam
Participant
May 17, 2008 at 12:55 pm

How about a common source for one inch O.D.—7/8 I.D. aluminum tubing?

mjohnson6565
Participant
April 17, 2008 at 8:18 pm

Yup when I bought the pvc pipe, washers and scotch-brite the guy asked me what I was working on….if he only knew 😈

riffraff
Participant
April 17, 2008 at 7:21 pm

I bought ACE out of stock 3 times already. The guy looks at me funny when I bring weird bags of parts to the counter now.

I can see his wheels turning, hes probably asking himself “what the hell do you do with 25 rubber washers and 5 grub screws?

bodhisdad
Participant
April 17, 2008 at 5:22 pm

Ace is the place.

mjohnson6565
Participant
April 17, 2008 at 5:10 pm

I had tried Lowes, Home Depot and Wally World with no luck however I was able to find them at Ace. Thank for the suggestions.

savagesam
Participant
April 17, 2008 at 6:05 am

Or go to a shoe/boot repair shop and ask if they have any scrap rubber. I always did.

riffraff
Participant
April 12, 2008 at 12:05 am

Like everybody else said, Ace Hardware is your place.

Look for the box labeled “Fender washers” with a sidenote saying they are made of neoprene. I found mine just under a box labeled “Neoprene washers”, which were all too large for the intended task, go figure. 🙄

Ace will also have a large selection of O-rings if you need them.

shrpshotr28
Participant
April 11, 2008 at 10:43 pm

as said, lowes, ace hardware, etc. check out the plumbing section where they keep parts for fixing faucets and such. I use 7/8od nylon faucet washers (had 1″ same deisgn in my ss before I got the frame extension) that happened to be beveled on one side; faced the bevel toward the muzzle to help direct air away from the bore of the shroud. Think they were 30-40 cents apice or so. The ones I got had a 3/16 hole but drilled out very cleanly with a sharp 5/16 bit.

voltar-1
Participant
April 11, 2008 at 8:16 pm

buy rubber gasket material and cut out your ‘washers’
’tis how I would do it.

mjohnson6565
Participant
April 11, 2008 at 7:25 pm

I was looking for something to use in between the metal fender washer and my other shroud material. So something with a 1″ OD and a 3/16 internal hole.

walkonking
Participant
April 11, 2008 at 6:41 pm

What size and thickness are you looking for? Ace hardware usually has a lot of stuff like that you can not find easily elsewhere.

Viewing 12 replies - 1 through 12 (of 12 total)

  • You must be logged in to reply to this topic.

6 Comments