Visit Talon Tunes
Updated on January 18, 2020
m.elserafy1985
Participant
January 18, 2020 at 5:58 pm
Q:

Taipan veteran regulator inquiring

Hi sir
How can I increase regulator pressure up to 10 bar ???
How many turns ??
CW or ccw ???
Thanks a lot

Taipan Air Rifles

All Replies

Viewing 15 replies - 1 through 15 (of 28 total)

1 2
Tom
Participant
May 24, 2022 at 5:13 pm

Crickets

Tom
Participant
May 19, 2022 at 8:39 pm

Crickets…..

Tom
Participant
May 19, 2022 at 9:44 am

Huma reg setting for a 25 long please?

Any help for the .25 is badly needed.

Plenty of .22 info around, nothing on the big hammer .25

cilami
Participant
August 31, 2020 at 7:14 pm

Appreciated!

anthony266
Keymaster
August 30, 2020 at 3:57 pm

Hey C,
In my opinion the Huma regulator is just a much better consistent unit..
Tony

cilami
Participant
August 30, 2020 at 3:02 pm

Thanks Tony

So apparently the Huma is at least as good as the oem reg., or even better according to your numbers?

  • This reply was modified 5 years, 7 months ago by cilami.
anthony266
Keymaster
August 26, 2020 at 12:43 pm

I just finished a tune on a 177 Taipan veteran standard and installed a Huma regulator here are the results…

cilami
Participant
August 26, 2020 at 10:54 am

Mik, How the Huma reg. compares with the oem in your Taipan Mutant shortie?

  • This reply was modified 5 years, 7 months ago by cilami.
  • This reply was modified 5 years, 7 months ago by cilami.
kris
Participant
February 3, 2020 at 5:53 pm

is that number on the stem the original output setting? probably as mine was very close to that number, so probably not a serial number lol

can someone else confirm similar for a .22

kris
Participant
February 3, 2020 at 5:18 pm

if you go that deep probably you will find that you have to clean out the contamination, mine had some orange gunk in it. including the internals of the reg. I would remove the 2 bolts on the base without touching anything else and measure the position of that nut what has the holes around it -against both ends of the middle screw. With calipers before you make any adjustments. Any tweaking will be relative to this reference.

a huma is good choice too, used to be able to request the exact set pressure before ordering, not sure if they still do this,
you can get around the need of the reg tester doing both approaches.

by the way the original reg is very good. better than the huma IMO.

m.elserafy1985
Participant
February 2, 2020 at 9:36 pm

This taipan response

zonk
Participant
February 2, 2020 at 8:06 pm

LOL slip of the finger! If you need John’s phone number let me know.

Zonk

Anonymous
Inactive
February 2, 2020 at 5:45 pm

Never mind got it. Was sopposed to be hagantool@aol not hangantool lol!!

Anonymous
Inactive
February 2, 2020 at 4:34 pm

Hey Zonk tried that email addy was returned mail back instantly. As unable to deliver at that address.

Anonymous
Inactive
February 2, 2020 at 8:12 am

Thanks Zonk!

Viewing 15 replies - 1 through 15 (of 28 total)

1 2
  • You must be logged in to reply to this topic.