Great piece of craftsmanship! I wish i had those skils
They look fantastic on the Leshiy

Did you made the second one for me? :biggrinn:

Cheers Huub

cheers huub

I was wondering if someone has some experience with this model Vector 2-12×32

The eye relief of the Vector 2-12×32 is 89-100 what is about the same as the…Read more

When you extend the pressure tube, you can only use silencer smaller or equal then 28 mm. Of course this is not a problem, but most used silencers like the HW or the Decimeater are larger in diameter.

On the old types of BSA and also Hatsan who has only a few mm between barrel en tube you couln’t use silencer at all anymore if you…Read more

cheers Huub

If you only use 0-rings to close the regchamber, and no venthole, there will be a bit pressure in the chamber after some time, because the 0-rings will never…Read more

I’m glad you like your new toy!
Please ask Egon to check the packages i sent to him. The manual should be in there. Although it’s a very small book and it’s in russian.
I do have here the certificate of the rifle. if you can mail your adress i will post it. I don’t know if the certificate mates yours or the other cricket.

I think the…Read more

It’s indeed a shortend bsa barrel, best there is.

By the way got identical new viking here, for sale

cheers huub

I indeed used a breech and pressuretube of a bsa.

huub

The barrel is pretty short, 19 cm total 😀
HW100 could be posible to, but the stock of a hw100 is pretty expensive and i don’t use it…..
But if you want one 🙂

Vented bushing what connects silencer to part behind the barrelband

All parts before sandblasting and anodizing

Rough stock milled out with action in it
😀

Home brewing anodizing 🙂

All finished parts after anodizing and color bath

cheers huub

It’s a leapers bugbuster 6×32 scope, later on replaced for a accushot 3-12×42 also compact but with a better crosshair

huub

If you have enough money, you don’t need to be gifted with skills 😀

i’ll make some pics of my home build router table

cheers huub

you could make the forestock about 4 mm wider on both side then the tube. After that glue a 4 mm piece of mdf on it and sand it down from 4 till 0 mm to get the angled shape.
I did use a hand router for the inletting, just place it upsidedown and make a side guidance. Then you can make a perfect inletting in small steps.

Can make some…Read more

I use several layers of polyesther spray filler used also for carpainting.
Do not forget the inside of the stock!

Another important thing for MDF is use high density mdf and not the cheap and light weight mdf.
When you want to screw something into the wood in the length direction, always drill and use 2 extra screws right angled to…Read more

I made several stocks from mdf, check my topic of the “Edsan bullpup”
The trick is to seal the stock right before painting

cheers huub

http://www.gunpower.org.uk/faq.html

to get 20 flbs with 14 gn you need a pelletspeed of about 800 fps.
When you look at the shotstring you see it climbing all the way, so hammerstroke isn’t powerfull enough to open the valve, or in other words the regpressure is much to high.
When you lower down the regpressure a lot (+/- 100 bar) and start with a weak hammerspring tension…Read more

you can pm me if you want one 🙂

cheers huub

please check this topic of another build of me with a BSA there you will find your info

cheers huub

http://talonairgun.com/forum/viewtopic.php?t=18720

The ultra was mine, but yes, it has been visiting Norway for the sidecocking 🙂

got some more pics of the build if you like

cheers huub

cheers huub

my adaptor is black anodized (this pic is not of my talon)

some more pics

Roar has one of my ultra’s at the moment and we are working on a 10 shot’s regulated bullpup right now….So yes he’s very very good.
I contacted Luchtbuks.com last week for a lelya in .22 and he said, Edguns are fabulous guns i wish i could get more of them. Leadtime at the moment is about 6 months…… Perhaps the Matador is on stock…Read more

Been on the russian forum with google chrome translate…..but even google doen’t seem to understand russian 🙂
But if it not to complicated you can make something of it 🙂

Just get’s in my mind, we have a common friend, Egon, who also had a Lelya and I’am pretty sure he took it appart so I’ll ask him too

i have seen these instructions, but they don’t give instructions for adjusting.
But if you look @ 2.26 min you can see the reg and the reg-chamber. And if i see it well there is a screw on top of the reg, so it should be posible. I just don’t know if there are other items. Normaly it a mather of increasing the pressure in the reg and find…Read more

as said in the titel 😆 it’s a .177
and it’s measured with the normal jsb exact

If the .22 has the same internals (reg) then it should be possible to increase the pressure setting of the .177 ??

grz huub

The inletting is made on the mill by a friend of mine.

The shroud is working fine. Not as quiet as i would like but it only 10 cm long.
The internals is treathed with 1/2unf and screwed directly on the barrel. the hole is concentric. The shroudtube is screwed on the barrelband.

Can make a pic if you want

The stock is rubber-coated

huub

What about an update of this topic

cheers

huub