Talonairgun | killerqueen33 | Activity https://talonairgunforum.com/members/killerqueen33/activity/ Activity feed for killerqueen33. Thu, 09 Jul 2026 01:06:06 -0400 https://buddypress.org/?v= en-US 30 hourly 2 1415873623e80d74729c6a2ef0049c32 killerqueen33 replied to the topic Teflon Tape in the forum General Chat https://talonairgun.com/forums/topic/teflon-tape/#post-196671 Tue, 25 Feb 2014 13:03:41 -0400 I use Loxeal 58-10 for threads on my pcp’s or HP systems up to 700 bar but it’s a tad hard (not impossible)to dismantle without air heating at about 200 degrees .
For 0-250 bar range the 18-10 (if i remember right) could do the trick ,.It replaces P.T.F.E. tape and dismantling easily.Just need a couple of hours for a completely dry.

]]> e5a7792f6f88ab0586c8b8865f6f451e killerqueen33 replied to the topic Okay for you math and or air tank gurus... in the forum General Chat https://talonairgun.com/forums/topic/okay-for-you-math-and-or-air-tank-gurus/#post-188871 Sat, 28 Dec 2013 07:50:02 -0400 I hope this help you Joe.
http://www.airgunsofarizona.com/Tanks/FillCalc.html.
If you have a small air compressor and you are able to find a cheap used haskel pump with at least 1:30 ratio from Ebay, i could advise you how you can make a poormans HP compressor depends the price you’ll get from the seller.Some of them sells them(Air driven liquid…Read more

]]> f44cd8ab3b54e8cb68ac639f08062dd4 killerqueen33 replied to the topic New guy Making a 257 Condor in the forum General Chat https://talonairgun.com/forums/topic/new-guy-making-a-257-condor/#post-187013 Mon, 16 Dec 2013 07:43:30 -0400 quote Tofazfou:KQ,

thanx for the LUBE heads up. See, i’m no expert…lol! But I will try your recommendation on the next casting/lube session

Ced nobody’s an expert.Everyone make his own decisions and experimenting on something until find it works…then just share his experience with other people.
For example neither you or me knew about…Read more

]]> ba92f01c9c2e75ccc766a17fc5911dee killerqueen33 replied to the topic New guy Making a 257 Condor in the forum General Chat https://talonairgun.com/forums/topic/new-guy-making-a-257-condor/#post-186711 Sat, 14 Dec 2013 19:29:45 -0400 Gary welcome on TAG and .257 WORLD.
As a bullet lubricant you can use Silicone shock oil for RC cars too.
Something most people have ignorance about,is that you have to avoid mix the silicone with other solutions because this way you can cause loss of silicone benefits which give even better performance and superior lubricating ability.
Personally…Read more

]]> 3d55e266c377f0a2c67e8cfd9b813cf2 killerqueen33 replied to the topic The people on this forum are assholes in the forum General Chat https://talonairgun.com/forums/topic/the-people-on-this-forum-are-assholes/page/5/#post-185330 Fri, 06 Dec 2013 12:23:48 -0400 quote Killerqueen33:quote Tofazfou:The TAG is awesome

TAG was Awesome until RoachCreek gave up airgunning .
I wouldn’t be bothered what other “Assholes” say if he was still here.
…I missed you Sir..!!!

Anyway life keep going and Tag for me is by far the Best and most serious airgun Forum and have three great lads under it’s management….Don’t…Read more

]]> 9a03f79c0216e22a4b094e53d5f2f611 killerqueen33 replied to the topic Please share experience with machined metal breeches? in the forum Mods/Machinists https://talonairgun.com/forums/topic/please-share-experience-with-machined-metal-breeches/page/2/#post-180735 Fri, 04 Oct 2013 14:37:30 -0400 What caliber that breech was used for?

]]> 38d16deef35676638c8ae69e36f586d0 killerqueen33 replied to the topic Please share experience with machined metal breeches? in the forum Mods/Machinists https://talonairgun.com/forums/topic/please-share-experience-with-machined-metal-breeches/#post-180733 Fri, 04 Oct 2013 14:21:04 -0400 This seems like a Dieseling.
Be careful what you lubricate pellet/bullet with.
If i m right you are lucky that nothing pass through your tank.

Maybe a wrong material like this one i was mentioned at “titanium tube” topic …who knows.. 🙄
The fact that someone are engineers doesn’t means they Know about metallurgy.Metal world is like the…Read more

]]> 58ed2d35fa7123ffe3227c6bcd9d1fe1 killerqueen33 replied to the topic Bore Polish/Paste in the forum Other Guns https://talonairgun.com/forums/topic/bore-polish-paste/#post-179929 Tue, 17 Sep 2013 09:17:07 -0400 For firelapping mostly i use the wheeler engineering kit .
Don’t try 220 grit,its too abrasive.You can go ahead with 320 and 600 but inspect every 5 shots for each one of them.
Also as a final finish i use Flitz and J-B paste.
The first one is around 800grit and the second one 1200grit.
Be carefull,you don’t need an extremely mirror…Read more

]]> 9e7206fedf64e9e3830f117dbc6a57ed killerqueen33 replied to the topic Looking for cam/cad files in the forum General Chat https://talonairgun.com/forums/topic/looking-for-cam-cad-files/#post-179905 Mon, 16 Sep 2013 22:03:07 -0400 What about a Lazer CNC?Do you have access on that?
I am experimenting to a Af trigger but my CnC’s are busy enought and i dump if i ll find the time to finish this.

The only thing is missing are two grub screws for 1st and second stage to the sear next on the trigger.

Right now I m trying to make an even better one but my busy time…Read more

]]> 52eebe8ae064e17c5734333f72cefc4d killerqueen33 replied to the topic 1.250 inch barrel od in the forum Mods/Machinists https://talonairgun.com/forums/topic/1-250-inch-barrel-od/page/2/#post-179138 Tue, 03 Sep 2013 19:46:09 -0400 Did i mentioned anything about Midwayuk.com?They don’t even sell barrels anymore.
Try http://www.midwaydeutschland.de …Go to AGB(left corner at the bottom of the home page)and read “Ziffer 10”.

]]> 9562f12b7e3adc9dd3d25c902d20ea5d killerqueen33 replied to the topic 1.250 inch barrel od in the forum Mods/Machinists https://talonairgun.com/forums/topic/1-250-inch-barrel-od/#post-179133 Tue, 03 Sep 2013 19:11:29 -0400 Give me what you read.

]]> 0a7e1bc8d2eb19754b06008109a2b7a3 killerqueen33 replied to the topic 1.250 inch barrel od in the forum Mods/Machinists https://talonairgun.com/forums/topic/1-250-inch-barrel-od/#post-179039 Mon, 02 Sep 2013 17:59:53 -0400 quote gabi.nechita:Hi Killerqueen33
I think Midway dont ship out of country.

How did you know that?Did you contacted them?

]]> 57bfe3e877f3ba8910b427b8ad3a1c38 killerqueen33 replied to the topic 1.250 inch barrel od in the forum Mods/Machinists https://talonairgun.com/forums/topic/1-250-inch-barrel-od/#post-179006 Mon, 02 Sep 2013 12:35:46 -0400 quote Marc:Track of the wolf sells tj liners. They ship to Europe.

I found this to the “Track of the wolf” site mentioning this message about barrels…“Not for Export. Until recently, we supplied the best barrel liners to refresh the bores of antique rifles worldwide. Homeland Security now requires a $2,400.00 license, plus a $300.00 permit…Read more

]]> 30715a41ffb6fac8e7b748ffc67c9d3b killerqueen33 replied to the topic Air Rifle Advice wanted in two cost brackets in the forum Other Guns https://talonairgun.com/forums/topic/air-rifle-advice-wanted-in-two-cost-brackets/#post-178953 Sun, 01 Sep 2013 23:28:42 -0400 Tell your friends to put their hand a little bit deeper inside their pocket and buy a used Tarantula or a Hogan Ripley Elite(plus filling equipment),if they can find them.
The second is one of my most favorite BB’s.Accurate as a pendulum,uncompromising quality,lightweight,reliable,comfortable.
The long-barrelled model gives 55ft/lbs at .22 and…Read more

]]> 3cbd29b5e32104c9daed40421af441e7 killerqueen33 replied to the topic Sightron 10-50x60 SIII 30mm Riflescope in the forum Optics/Nightvision https://talonairgun.com/forums/topic/sightron-10-50x60-siii-30mm-riflescope/#post-178831 Fri, 30 Aug 2013 21:27:00 -0400 I own the old one with mil-dots(LRMD) and i got the 6-24x50LRIRMOA 2 days ago.

The 10yrd maximum focus feature you mentioned is good but personally i don’t like the elevation travel so this time i chose the little brother which have 100 instead 50.
Besides i think that this kind of Magnification(10-50x) is useless on Airguns.

For me by far the…Read more

]]> 3d6d07884016925e7c609bd30e13d842 killerqueen33 replied to the topic manufacture air cylinder in the forum Mods/Machinists https://talonairgun.com/forums/topic/manufacture-air-cylinder/page/3/#post-178437 Sun, 25 Aug 2013 11:36:46 -0400 I do read them and know what does Omerta means.Therefore never find you on them (note/books)but if i will someday,then you ll need luck 😆 .

]]> cf226a3adadd0e62524e3343aa4e93c2 killerqueen33 replied to the topic manufacture air cylinder in the forum Mods/Machinists https://talonairgun.com/forums/topic/manufacture-air-cylinder/page/3/#post-178435 Sun, 25 Aug 2013 10:06:08 -0400 I dont care what did you test …..you can test it even at 1.000.000.000.000.000.000.000 x 10³psi…it doesn’t make sense to me because i spend half of my life under Hangars and i know titanium and air better than you and don’t give a shit if you and other members don’t know me because neither do i.
Titanium looks strength under HP but its…Read more

]]> 250dc7ace60f0a30a425e897cfb1a2af killerqueen33 replied to the topic A 257 Cast Bullet Reference Guide in the forum Other Guns https://talonairgun.com/forums/topic/a-257-cast-bullet-reference-guide/page/4/#post-178286 Sat, 24 Aug 2013 00:39:13 -0400 You rock..!!!! I like the way you think and shoot !!!
What is the material of the board…pvc?

]]> 4356db72956d452d54100ae7ce6d44c2 killerqueen33 replied to the topic Air Usage in the forum Mods/Machinists https://talonairgun.com/forums/topic/air-usage-d28/#post-178060 Tue, 20 Aug 2013 18:56:58 -0400 Caboose
Believe me,sniping based on calculations but air usage is another parameter and i think all these are bullshits…the most important thing is trial and errors than theory.
For me it is better to make a testing system and experimenting .
A testing valve with an adjustable inlet wheel (like Air Arms or Fx),and a testing breech with an…Read more

]]> fc2c395e28a0e606483d0498d0470684 killerqueen33 replied to the topic Scope riser rail in the forum General Chat https://talonairgun.com/forums/topic/scope-riser-rail/page/2/#post-178048 Tue, 20 Aug 2013 15:54:10 -0400 Does the Tri-rail a riser mount?..i thought it is a scope extension mount to add some height on it ….sorry if my bad English do not help me to realize this term.
At least 80 GRIT seems to like the idea of an adjustable mount…if i wasn’t mistaken maybe he will never finding infos about it… 😀

]]> 7f8b82bbb0d4657b26daf9efb7c8f963 killerqueen33 replied to the topic Air Usage in the forum Mods/Machinists https://talonairgun.com/forums/topic/air-usage-d28/#post-178038 Tue, 20 Aug 2013 05:53:43 -0400 .25cal
1st shot.. if you shoot without bullet (free flow)normally you must spent 68.8psi for the first 2 feets supposed that the valve is already closed once the bullet leave the barrel(i m saying that because it is impossible to calculate the valve timing for more accurate calculation ) ..but..with a loaded bullet your pressure being 52psi less,…Read more

]]> bcdb0fb29295209c9299322a86335905 killerqueen33 replied to the topic Air Usage in the forum Mods/Machinists https://talonairgun.com/forums/topic/air-usage-d28/#post-178033 Tue, 20 Aug 2013 04:48:16 -0400 what is your air reservoir capacity?

]]> 4f9f76d5a17d20e620dfca38b45dee73 killerqueen33 replied to the topic Air Usage in the forum Mods/Machinists https://talonairgun.com/forums/topic/air-usage-d28/#post-178015 Tue, 20 Aug 2013 00:38:24 -0400 Lets say we have a .22 barrel 24″in lenght..this is .3cu/ft of volume at free atmosphere.
according the Boyle’s Law it is Va = pc Vc / pa

where
pa = atmospheric pressure (14.7 psia, 101.325 kPa)

Va = volume of the gas at atmospheric pressure (cubic feet, cubic meter)

pc = compressed pressure (psi, kPa)

Vc = volume of the gas at compressed…Read more

]]> 30ebff4d54508e09da01674c6ab6d316 killerqueen33 replied to the topic Air Usage in the forum Mods/Machinists https://talonairgun.com/forums/topic/air-usage-d28/#post-177997 Mon, 19 Aug 2013 18:59:04 -0400 its easy…imagine the barrel bore like a cylinder and volumetric with a calculator like this.
but you have to add 60-70% (160-170% overall volume)of the result (depending the caliber)because during the pellet/bullet movement ,the distance between pellet and valve increased and pressure drops a little bit while the valve has already closed and…Read more

]]> 43df3735d40918abb24c6fcbe99039f5 killerqueen33 replied to the topic Scope riser rail in the forum General Chat https://talonairgun.com/forums/topic/scope-riser-rail/page/2/#post-177993 Mon, 19 Aug 2013 18:25:47 -0400 Thats right…They are made to fix this problem, and in our case take advantage of that feature to adjust the elevation on Long range shooting.

A long time ago Pyramidair have one 11mm to 11mm dovetail but it is not available any more. http://www.pyramydair.com/images/acc/B-Square_177011_299.jpg .I m talking about B-Square 17011.

Ohh…i forgot…Read more

]]> 452f723d3e07effa56c42482da9e2c6f killerqueen33 replied to the topic Scope riser rail in the forum General Chat https://talonairgun.com/forums/topic/scope-riser-rail/#post-177990 Mon, 19 Aug 2013 18:09:08 -0400 Synthetic,

This mount we are talking about doesn’t change mounts height.
It can be adjustable only from the rear edge of the mount.The front edge remain steady on a hinge.That way changed the incline of the scope in order not being parallel to the rifle rail.

]]> 3e509aa0d34e35e341f4ee4e0e21a951 killerqueen33 replied to the topic Eye dominance in the forum General Chat https://talonairgun.com/forums/topic/eye-dominance/#post-177979 Mon, 19 Aug 2013 09:45:51 -0400 it helps a lot.
At least your theory can explain why recently i discovered that my no -dominant eye works like the other because it turns dominant without knowing about this for a long time.
In fact i have two dominant eyes right now but prefer that one on the same side with my “sensitive-st” trigger finger.

]]> 1edcccd5b456b93c8e9d3fd19883911a killerqueen33 replied to the topic Scope riser rail in the forum General Chat https://talonairgun.com/forums/topic/scope-riser-rail/#post-177977 Mon, 19 Aug 2013 07:41:56 -0400 if you did read this stupid comment on Amazon,obviously you dont read this to the end of the review.

***ADDITIONAL NOTES/UPDATE***
I have since heard from other people who have used this adapter who have explained that it should have the hinge facing forward, whereas I had mine facing rearward.
That would still not have worked on my specific air…Read more

]]> 6cba5ff6a30530654f327680a8ae0703 killerqueen33 replied to the topic Scope riser rail in the forum General Chat https://talonairgun.com/forums/topic/scope-riser-rail/#post-177971 Mon, 19 Aug 2013 05:19:26 -0400 LoL….This guy must overtight the lock screw and damaged the adjustment screw threads.I put Blue locktite on mine and leave lock screw a little bit tight.
Although i am almost sure that the Guy fit his mount on a 350Magnum Diana or something,to cure the barrel drop…Have you ever shoot one of these???…impossible avoid mount damage..recoil as…Read more

]]> be1e298a985bb303032b60c17c2eac57 killerqueen33 replied to the topic Scope riser rail in the forum General Chat https://talonairgun.com/forums/topic/scope-riser-rail/#post-177924 Sun, 18 Aug 2013 14:10:29 -0400 Another one great product here …Matlip,this is for you my friend…I think 7.4″ may not being 200+ but it is long enought 😉
This is a B-square mount like mine in to editions…short and long.I prefer short for more pivot ability.

]]> 363027d5ddfbd021cc21264e26770523 killerqueen33 replied to the topic Scope riser rail in the forum General Chat https://talonairgun.com/forums/topic/scope-riser-rail/#post-177923 Sun, 18 Aug 2013 12:52:00 -0400 Joe.
B-square is a very quality company and it located in Jacksonville, Florida.
About the Riser i will not advised you to check their site because it is very poor but if you want take a look here
Type in “B-Square 17021” and “B-Square 20062″at Google…This is what i have for personal use.
This way i can rise the scope wherever i want without…Read more

]]> 46f39cdb6070c40264469dcf0dc987a2 killerqueen33 replied to the topic manufacture air cylinder in the forum Mods/Machinists https://talonairgun.com/forums/topic/manufacture-air-cylinder/page/3/#post-177850 Fri, 16 Aug 2013 20:32:32 -0400 quote blodnob:As far as im ware you cant anodise black.

Thats another reason why i don’t use titanium..

Anyway..4130 umber alles..

IMAO,maybe 7075 and titanium can handle very easy this kind of pressure but what about elongation?
4130 steel remains where it is even after 1000 years of daily air filling/release.
Take an aluminum or titanium wire…Read more

]]> ef09e6e997df6aff387cfc322cb28cd3 killerqueen33 replied to the topic Utube of 280 yard Haley shot on the 8" gong in the forum Other Guns https://talonairgun.com/forums/topic/utube-of-280-yard-haley-shot-on-the-8-quot-gong/#post-177798 Thu, 15 Aug 2013 23:06:24 -0400 Is this video with the Handycam or casio?
Is there a software coming with the casio Exilim in order upload videos or convert to the right file?
Saying that you have a bad time to figure out how to load it to utube make me thinking about it.
You post videos since two months and you still don’t use on it?
Man ..i don’t want spending my free time on…Read more

]]> 6b54dc056cbd7b7a320e89ec1d8bdc08 killerqueen33 replied to the topic Utube of 280 yard Haley shot on the 8" gong in the forum Other Guns https://talonairgun.com/forums/topic/utube-of-280-yard-haley-shot-on-the-8-quot-gong/#post-177793 Thu, 15 Aug 2013 22:15:11 -0400 What camera do you use.I think purchased one and post my results too.
Randomly i use my Mobile phone only for image posting.
You have to see me shooting at 400m with my “new” eye and my next favorite caliber….far superior than .257… I shoot sparrows in the eye from that distance…:D

]]> a8097601fb48b7104f7b1a94ced5360c killerqueen33 replied to the topic most powerfull condor air rifle design in the forum General Chat https://talonairgun.com/forums/topic/most-powerfull-condor-air-rifle-design/#post-177780 Thu, 15 Aug 2013 14:54:12 -0400 The whole Gun and bullet mold for those cast bullets seems being custom made.
Noticed the screw instead a trigger and how square(not round corners like condor) is the cutting area of the frame after milling process .. 😀
Or look at last image inside the breech. where is the original driving slot for the Cocking knob? must be at 12o’clock under…Read more

]]> 8a382e9d51ebdf3daf830a0bde95a6cb killerqueen33 replied to the topic most powerfull condor air rifle design in the forum General Chat https://talonairgun.com/forums/topic/most-powerfull-condor-air-rifle-design/#post-177776 Thu, 15 Aug 2013 08:59:48 -0400 quote RiffRaff:I think that piano has seen its last saloon.

The other end of the spectrum.

I suspect incorrect lighting though.

No incorrect lighting i suppose.I think he removed the steel piece inside a Prometheus pellet and left only the plastic.Thats why it weights 1.4gr and easily surpass this…Read more

]]> 6a3b5ef8c92653b5ae790534bd5e0dd3 killerqueen33 replied to the topic Scope riser rail in the forum General Chat https://talonairgun.com/forums/topic/scope-riser-rail/#post-177774 Thu, 15 Aug 2013 06:53:22 -0400 I have weaver rings fitted on the weaver rail of my Riser bridge mount which have a dovetail to the bottom and fit in guns 11mm built in male dovetail.

Every gun it’s not the same….For example you can use normal low to medium rings on that riser for a AF because i know that eye placement , while you do shooting is too low so you need more…Read more

]]> 1f1f67ecfeda22c5571483ca3352ef58 killerqueen33 replied to the topic Scope riser rail in the forum General Chat https://talonairgun.com/forums/topic/scope-riser-rail/#post-177658 Tue, 13 Aug 2013 16:17:29 -0400 You don’t need 200+ one because it does not exist at least as a riser(only standard like AF tri-rail one)….you need something likethis(Overall length is about 5.5″).
….and very low profile offset rings like Bsquare 21052 depends your scope (1 inch or 30mm).
I own both of them for LR shooting and i can assure you about the quality which is…Read more

]]> d3f8737acde59024479d550ed1a9ff28 killerqueen33 replied to the topic most powerfull condor air rifle design in the forum General Chat https://talonairgun.com/forums/topic/most-powerfull-condor-air-rifle-design/#post-177653 Tue, 13 Aug 2013 13:35:01 -0400 Honestly,if i was able to re-set the target everytime i shoot on it at 200+ yards i will give up airguning.
However the conclusion is that it can be done and this looks physical to me tuning a AF like this .
Also you have to be Sport Billy and carry those bullets in your magic size-changing gym bag when your hunting.
A true elephant killer for sure!!

]]> 3d03ce4cdbad32a34250b06720b463d8 killerqueen33 replied to the topic Eye dominance in the forum General Chat https://talonairgun.com/forums/topic/eye-dominance/#post-177561 Sun, 11 Aug 2013 19:21:14 -0400 Randomly i shoot with handguns.
So…My point is “rifles”.
When i was young i usually try to shoot by the right hand and i m a left eye dominant.
My grandfather teach me to shoot on the left hand and for the rest of my life i did this until a year ago.
Until then most of my favourite rifles are LH or ambidexious but i follow someones advice and…Read more

]]> add9945ec0e2707bc8b78f46043ab07f killerqueen33 replied to the topic manufacture air cylinder in the forum Mods/Machinists https://talonairgun.com/forums/topic/manufacture-air-cylinder/#post-175998 Mon, 22 Jul 2013 10:38:20 -0400 I suppose,wherever you can find 6061 or 2024… but its not so easy to find it online.
Try to drop a mail or a phone call to a commercial shop at your local area.They may supply you by request.
You see the problem is to find a tube.Otherwise round bars or sheets are available everywhere .

]]> a941ae1f013ebf954283cb0ca35ce1d1 killerqueen33 replied to the topic manufacture air cylinder in the forum Mods/Machinists https://talonairgun.com/forums/topic/manufacture-air-cylinder/#post-175987 Mon, 22 Jul 2013 05:29:39 -0400 Yes…you have to drive to NASA to get one.. 😆
7068 developed in the mid 1990’s by Kaiser Aluminum, and exclusively stocked and supplied in Europe by Advanced Metals International.
Tubes not stocked available to order on relatively short production lead-time.
However random lengths supplied or cut to customer requirements

Therefore if you f…Read more

]]> 5834a1597b4e6e8c1aa44b7d99c19abd killerqueen33 replied to the topic manufacture air cylinder in the forum Mods/Machinists https://talonairgun.com/forums/topic/manufacture-air-cylinder/#post-175944 Sun, 21 Jul 2013 18:28:18 -0400 You can use this calculator.
Just add the yield strength of the material of your preference.(you can find yield strengths on the onlinemetal.com metal guide )
Personally for that kind of pressure (200bar)i would prefer 7075-T6 aluminum for a strong,lightweight air tube.
My custom air tube can keep 350+bar as the maximun of my daily needs EASILY..…Read more

]]> a951980c722f9bcf0577597e2d9522a9 killerqueen33 replied to the topic utube video of 502 yard Haley 257 12 oz kill in the forum Other Guns https://talonairgun.com/forums/topic/utube-video-of-502-yard-haley-257-12-oz-kill/page/2/#post-174334 Mon, 17 Jun 2013 17:59:39 -0400 Yes,the only change i done is the barrel body.
I get a new one and i cut more the space to the bullet feeder…I made a larger Prode too.
Right now i get 280 FPE at 280 bar.
For over 320bar must fill the tube straight from my compressor because i haven’t a diving bottle over 300bar but i intent to buy one soon.

]]> f283befe811a65a0909edac55dd97992 killerqueen33 replied to the topic utube video of 502 yard Haley 257 12 oz kill in the forum Other Guns https://talonairgun.com/forums/topic/utube-video-of-502-yard-haley-257-12-oz-kill/page/2/#post-174326 Mon, 17 Jun 2013 15:39:33 -0400 No never tried a Kreiger barrel.
I was almost ready to order a Hart barrel due Oldgoat’s advice at “Mihec Mold topic” but finally i choose a Shilen after read several good reviews about them and i m really happy with my purchase.
Do you remember i told you that i got 4 barrels…two .257 and two .308… Right now i m experimenting at .308cal and i…Read more

]]> 7d1ed6f76338cb7f30ccb6393aaa3631 killerqueen33 replied to the topic utube video of 502 yard Haley 257 12 oz kill in the forum Other Guns https://talonairgun.com/forums/topic/utube-video-of-502-yard-haley-257-12-oz-kill/page/2/#post-174318 Mon, 17 Jun 2013 10:38:43 -0400 quote roachcreek:KQ,

I fire lapped the 1-10 yesterday with the two finer grits in the three grit Wheeler fire lapping kit.

Instead of shooting 5 rounds and cleaning I shot one round and cleaned with 320 and 600 grit of which I shot 25 shots. It took a long time to do it but the results were well worth it.

I shot the 100 grainer at 280 yards…Read more

]]> f6599b357cea4b5c0f86727269d517d2 killerqueen33 replied to the topic utube video of 502 yard Haley 257 12 oz kill in the forum Other Guns https://talonairgun.com/forums/topic/utube-video-of-502-yard-haley-257-12-oz-kill/page/2/#post-174087 Wed, 12 Jun 2013 13:12:25 -0400 RC..do you know how many shots needs Mr.Bowman’s rifle until try to clean it?…My understanding drive me to conclude that after 40.000+ shots he probably do this every 100+ shots or none attempt.
I usually clean my barrel every 60-70 shots but not for accuracy lost…It just the way i use to manipulate all my barrels…Do you thing it’s…Read more

]]> 6d302ed158b2fd8a11f5bfd25a0bd7ce killerqueen33 replied to the topic utube video of 502 yard Haley 257 12 oz kill in the forum Other Guns https://talonairgun.com/forums/topic/utube-video-of-502-yard-haley-257-12-oz-kill/#post-174068 Wed, 12 Jun 2013 03:09:42 -0400 So…how bad shoot the NOE100gr under the 280yrd in your gun ?
mine shoot differently and unsized…maybe barrel manufacturing matters…I have a 1/10 shilen.

]]> 6b62830641b6c38756d55943cc9dcd71 killerqueen33 replied to the topic utube video of 502 yard Haley 257 12 oz kill in the forum Other Guns https://talonairgun.com/forums/topic/utube-video-of-502-yard-haley-257-12-oz-kill/#post-174057 Tue, 11 Jun 2013 22:11:47 -0400 RC…I noticed that you choose your NOE’s bullets on this challenge.This make me think that logically the most accurate of your bullets on your current set up chosen by you to accomplish your purpose.
It seems that my guess over here was right,saying that NOE 100gr will be a winner and that was before you received your 1/10….wasn’t it?

]]> eabef1c52547de5f702043ab603dc493 killerqueen33 replied to the topic utube video of 502 yard Haley 257 12 oz kill in the forum Other Guns https://talonairgun.com/forums/topic/utube-video-of-502-yard-haley-257-12-oz-kill/#post-173977 Mon, 10 Jun 2013 22:10:20 -0400 I don’t know what kind of natural ranges you have at US but here is very difficult to find one to shoot safely.
Usually i choose a natural barrier to mount the target like a small hill.
That event i described above was happen a month ago.I went to a wilderness beach,mount the target and then went backward to shoot it from a distance.
There was…Read more

]]>