I’ll do another run with lower power. It’s at about a setting of 9 right now. I’m not sure what you mean though. Deviation in velocity? Seems pretty linear to me. Maybe I don’t understand what you are getting at.

Definitely need to work on trigger control. 🙂

I called AirForce and ordered directly from them. They said 12mm is what comes in the .25 caliber SS and that’s what I needed to order for my Condor SS .22, if I want to swap to .25 caliber. Got…Read more

Gun: TalonP, with shroud
Power: 8
Pellets: JSB Exact 25.39gr

TalonP tank was filled to 3000 and dropped to about 2900+ when I turned off the main valve. I fired one empty chamber, before beginning.

These…Read more

I have White, Blue, Green and Red LED lights, from another project. Hooked up the white and they seemed to work but the few shots I tested weren’t always detected. Was getting a little over 800fps, with the JSR pellets and the TalonP. I think I might…Read more

Sounds like it didn’t work. 😉

I’m going to test it tonight I guess. I have some white LED strings. They have sticky back and can run right along the difuser. Just…Read more

I need to get a carbon fiber tank next week. My Spin-loc arrived for my CondorSS and it was completely empty. Took by 3000psi scuba tank to 2800 in one complete fill. 😉 Now I have to go refill it in the morning.

Indeed. I fired of about 25 pellets today and liked the results. Well, that is, considering my trigger jerk. I’m not as steady as I used to be. But this was my last 5 shot group, with a good hold. I actually think I…Read more

My JSB Exact arrived today. 25.39 gr. I also have some other JSB coming tomorrow, I hope. Ordered a bunch of everything, just to see what works.

I decided to try and remove some of the slack, while waiting for a ne bushing from Randy. He said he’d look for a tighter one. He believes my barrel is smaller than normal. It’s .475 (exactly). I believe it’s spec’d at a 12mm barrel which makes this about right (.472 +/-). Regardless, the solution seemed to be a better fit.

I bought…Read more

Already in…Read more

Barrel: .475″
Bushing (ID): .483″ (+.008″)
Original bushing (ID): .477-.478 (+.002-.003)

If screw is tight, the .008″ gap is all on one side of barrel.
If screw is loose, there is nothing to lock the barrel concentric with endcap.

At least this is the way it seems.

Comments?

My .257 has a smaller first baffle hole at .275″ and the shroud is 22″ long.

It’s not a .22 it’s a .25 and the longer barrels have an alignment device on the end of the…Read more

Anyone know what the hole diameter of the end cap should be for the 6″ R.L. shroud, for the TalonP? I have a perfectly sighted in TalonP (without shroud), but when I put the shroud on, and verify it’s perfectly concentric, pellets will graze the hole edges.

Mine measures .277. Some have suggested boring out to .3 but I’m…Read more

Do you still get good velocity using only 2500psi?

I was actually hoping to go to heavier pellets, at…Read more

That could explain a lot. I have been…Read more

Thanks

Then, I put the original end cap on. And test fired the gun. Flawless operation. Bullet impacts were within the area of a nickel (45′).…Read more

Will do. I do still have some issues. Somethings still not right. And the tophat worked loose again. Going to be ordering a tophat for my talonP, if they make one for that…Read more

I already love the gun.

quote Wildfire:You should contact Tony @Talon Tunes and order a one piece “quick change” unit from him. It has different size inserts so it is completely tunable.

First thing…Read more

I was about to tear my gun apart and began by removing the tank. I noticed the tophat had come loose and was who knows where and changing with shots. That explains why I had trouble closing the valve on some shots and definitely would have a consistency effect. Now to figure out where it should be. Good…Read more

I’ve got some domed 27.8 Benjamin and some H&N Barracuda 31.02 and two kinds of Eun Jim 43.2 and 35.8.

I need to find out for sure if I’m missing the washer or if the TalonP just has the o-ring only. I’ll call airforce if I don’t…Read more

That’s what I did. I just took it apart and checked and the white o-ring is snugly up against the power wheel. Looks like it’s where it belongs. No…Read more

That being the case, I would only see one of those o-rings right. The one on…Read more

hmmm… I removed the barrel, to install my R.L. Shroud. I watched their video first. I didn’t see…Read more

My 18″ .25 caliber barrel arrived today. I was also going to get a 24″ barrel but I think I’ll just buy another Condor with 24″ barrel.