Talonairgun | samurai | Activity https://talonairgunforum.com/members/samurai/activity/ Activity feed for samurai. Thu, 09 Jul 2026 01:06:06 -0400 https://buddypress.org/?v= en-US 30 hourly 2 137718cbc886bf105d93a4926cbe39a7 samurai replied to the topic New here... some questions if I may. in the forum Mods/Machinists https://talonairgun.com/forums/topic/new-here-some-questions-if-i-may/#post-96872 Sun, 24 Jan 2010 02:13:27 -0400 quote Hold over:I think talon tunes sells a drop in 25 cal, for around 180-200 bucks. and the hammers too.

Yeah, there is that, but I’m a cheap bastard. 😆

Plus, it gives me an excuse to buy more goodies for my lathe!

]]> 9a92488d60c6dead9edf662e22fafe2c samurai replied to the topic New here... some questions if I may. in the forum Mods/Machinists https://talonairgun.com/forums/topic/new-here-some-questions-if-i-may/#post-96814 Sat, 23 Jan 2010 07:31:58 -0400 quote Subssonic:when I got my barrel blank it was a piece of 3/4″ bar stock saw cut on both ends with a hole drilled and rifled in the middle….so in short yea you’ll need to turn the od and breach and make some bushings….no big deal of you take your time ….best of luck

Thanks!

So it looks like I’ll have to cut it down and crown the muzzle…Read more

]]> 24771d23b96be4401da9c83c0310c400 samurai replied to the topic how much do you pay for HPA ??? in the forum General Chat https://talonairgun.com/forums/topic/how-much-do-you-pay-for-hpa/page/2/#post-96812 Sat, 23 Jan 2010 07:03:50 -0400 Yup, $5 here at Sport Chalet in Las Vegas. They fill up to 4500psi. I recently talked with the gentleman there about buying a scuba tank. I politely told him what I was going to use it for, and there were no problems. Scuba tank for $150, with fill and inspection. It’ll work until I can afford an SCBA tank!

]]> ddda83245baeaf870005d4094a6cfd49 samurai replied to the topic Bipod on the SS in the forum Talon/Talon SS https://talonairgun.com/forums/topic/bipod-on-the-ss/#post-96809 Sat, 23 Jan 2010 06:03:37 -0400 I took the cheap route. I drilled a hole in the forearm, large enough for a 3/8 (I think that’s what it was) bolt. I then ground down two sides of the bolt head so it would fit snugly in the slot in the forearm. This keeps the bolt from rotating. Then, it was just a matter of cutting off and grinding down the bolt and drilling a hole through it to…Read more

]]> 2bdb1a060472decb013dac66497c83ab samurai replied to the topic New here... some questions if I may. in the forum Mods/Machinists https://talonairgun.com/forums/topic/new-here-some-questions-if-i-may/#post-96794 Sat, 23 Jan 2010 01:57:28 -0400 Thanks for the replies everyone! After a little more thinking and tinkering away in my garage (just vented both frames, both front bushings, and did the trigger mods), I think I’ll be keeping the barrels 18″ or under. Reading around the forums, it seems like folks are able to get around 900fps with the 12″ using a heavier hammer and Condor valve.…Read more

]]> 91bb3eacb74cf16ec29547b46337e02d samurai replied to the topic New here... some questions if I may. in the forum Mods/Machinists https://talonairgun.com/forums/topic/new-here-some-questions-if-i-may/#post-96750 Fri, 22 Jan 2010 18:11:56 -0400 quote 80 GRIT:Why not keep one of them a shorty, and turn the other one into a sniper/long ranger??? If you do, and if you are running .22 cal, I will trade you my practically brand new, proven accurate, 24″ barrel from my condor for your 18″ barrel…Just a suggestion that will work out for both of us.

It seems having one in 18″ and one in 12″…Read more

]]>