Dyotat,

the gun is just less than a year old. I’ll check out the hammer for wear.

ALL OF WOK’s ACCESSORIES I HAVE BOUGHT ARE FIRST CLASS ❗ ❗

I realise that friendly ribbing does not:

A: Transfer very well over the internet

B: Most often fails unless you’re really close friends.

My apologies once more.

thank you.

quote knifemaker:I have never seen anything poorly machined, and or, over priced from WOK.
😕
Care to elaborate a bit more on WHY you are putting WOK’s work down?

Knifemaker,

a poor attempt at humour. My apologies if anyone was offended.

The wokgard 15 is a first-rate example of fine workmanship.

http://talonairgun.com/forum/viewtopic.php?t=13259&highlight=

-Viewer discretion advised. Contains very lax use of the term “beer”.-

Well done.

Mike

Thank you fotr the o-ring tip. And yes, the shot string is all…Read more

here’s a recent shot string from my 12″ barrel:

Stubby extreme .25, starting pressure 2800 psi, tophat set at 0.088, pw at 8, JSB Exact Kings 25.4…Read more

I got mine without the Maddog stock and with the TSS frame.
The Extreme valve is a powerhouse, but also consumes a LOT of air with a 12″ barrel if you want to go hot.

I’m keeping mine in the 875 fps region (with JSB 25.4 gr) and can get just about 20 useable shots per fill, starting from 2800 psi.

My .25 TSS with R&L Extreme valve gives 20 shots in the 870 to 900 fps range. JSB Exact Kings, 2800 psi fill. So 42+ fpe. But even with ten baffles it will never be backyard quiet.

Im sorely tempted to go with a 16″+…Read more

Bullets, pellets, arrows. All good.

Baffles inside?

Randy @ R&L will set you up with one powerful carbine.
Great service, too.

Here’s one version to adjust the trigger without doing any permanent damage 😀 . Works fine on mine.

http://fuzzylimey.net/projects/452triggermods.html

Polishing and honing CZ trigger/sear parts is a delicate operation, since some parts may be only surface hardened. If you grind away the hardened layer,…Read more

Please report the shot count once you have the time.

The stock is the best part of the deal. The regulator bit the dust after a couple of shots, the trigger linkage was missing half the screws and nuts straight from the factory.

I’ll give them the benefit of the doubt, but would likely…Read more

The Aquila does not work worth squat in my CZ: the 16″ twist rate is not tight enough to stabilize the bullet. Have not shot them through a suppressor lest an unstable bullet damage the baffles.

Wincester and Remington subsonic hollow points are my go-to ammo. Very accurate and quiet to boot.

Had a chance to roam the Sierras for a week or so several years ago, hiking and camping with my wife. Sequoia, King’s Canyon, Yosemite, Tuolumne and Mammoth Lake area. Truly a special area.

And nice fish, too. Some time ago someone here made an analogy between flyfishing and airgunning. Give it a shot. Have been…Read more

to boldly go where no Talon shooter has gone before..
Your exploration never ceases to impress me.

:bow:

Having fairly limited experience with modern airguns so far, I’d tend to claim that the suppressed pb:s I own…Read more

sent you a pm with my email info.

what sort of shot strings does your setup give?

http://talonairgun.com/forum/viewtopic.php?t=19217

I should have one from Randy in a couple of weeks, shall try my best to give a report once I manage to figure the gun out.

Don’t discount hardwood plywood, especially when this is your first. A good and…Read more

which valve?

So, I’m interested in cartridges with…Read more

if I may ask, what are you looking to have the gun do? This could help narrowing down the options. The ideal use of a Mini-30 is quite different form a long-barreled AR 308, for example. 😀

So true. I’ve had friends who were reckless with one or the other, ending up badly hurt or dead.

But enough OT here.

Dang, I had half forgotten how much I want a Royale..

Congrats.

:bow:

http://www.talonairgun.com/forum/viewtopic.php?t=22139

thanks for the input. Nice .22, btw. And we’re going OT here, but what the hey.

The Aguila SSS is a tricky one. I’ve only seen them stabilize out of Russian TOZ .22 rifles, with a twist of ~12″. With the common 16″ twist of .22 lr, the long and heavy bullets just don’t stabilize, making the use of a suppressor impossible. When in…Read more