Calibre: 4.5mm /5.5mm ( .177 / .22 )
Loudness: Medium
Barrel Length: 483mm ( 19″ )
Overall Length: 850mm ( 34″ )
Capacity: Single Shot
Cocking Effort: 2 lbs.
Barrel: Rifled & Fully Concealed
Front Sight: None
Rear Sight: None
Scopeable: Raised 11mm Dovetail
Trigger: 2 stage adjustable with…Read more

In Indian/Sanskrit literature

In Sanskrit and related Indic languages, Arya refers to one of high birth or caste. Although Aryas were concentrated in North India, the title of Arya was used with various modifications throughout the Indian Subcontinent. Kharavela, the Emperor of Kalinga…Read more

He has also posted an extensive review about the same in…Read more

quote jkaleido:Hi Spartan…Can you upload pics of the final version? where it is sold?

Thanks from Spain

quote slayer5:Do I have to dump the bottle if I ship it? whose responsibility is customs there? I assume the buyer knows what he has to do to getthrough customs if he lives there?

Only. .177 air rifels are allowed to be imported in India & that too if importer has valid shooting club membership. No commercial quantity is allowed. Parts like barrel, grip etc. are easily identifiable & custom may seize it. Anything related to guns or airguns is no-no for Indian customs.

I…Read more

Thanks

Visit following link. It contains info about

Universal Dry Pac Kit Instructions
Pump Assembly and Maintenance
Seal Replacement
Dry-Pac Story
Retro Fit Dry-Pac Instructions
Dry-Pac Test Results
Dry-Pac Instructions
Replacing Micron Filter…Read more

Cheers !!!

Did you find my work to be imperfect or out of tolerence for any reason? Please let me know so that I can rectify my mistakes. What exact precision work you intend to carry out beside enlarging transfer ports…Read more

knifemaker, with all respect to your abilities & experience. The work you do on your knifes is super duper precise for us & I really wish to make products of that caliber one day…Read more

Cheers !!!

The one you saw is capable of doing precision work. Most of my final polishing & port extensions are done on this bench only. You too can achieve it after little practice.

Mistman is it hard to get tools there?

😥 😥 😥

Hey Adam,

I have seen the models where you can attach a hand drill and thereby it does the job of a Bench press drill.

Though not 100% but pretty close….Ifs so then I can get it down here…..

Is it the one you saw at my home?

Thank you very much tagdagger. I was using 0.60mm. Now let me try with this wire.

Wow 34″ barrel, is it rifled or smooth bored?

barrels are measured to the grooves

why would you want to measure to the lands?

LW is .216 bore and 0.221″ to grooves…Read more

21grains- Talon in 0.22 -70grams Brass…Read more

Because of your suggestions pin pointing problem areas I could solve the riddle.

There were 4 causes. Bad pellet material, undersized barrel, rough stem, & loose ‘O’ ring in breech.

Today I carefully removed the stuck pellet & found it slightly mashroomed around barrel breech end which made it virtually impossible to be pushed…Read more

Try different pellets of different sizes and use the pellet that groups the best.

Sam

Dear my problem is not resizing the pellets but I want to know the exact cause of tank dump because it normally…Read more

All other pellets with maximum 5.55mm skirt size are doing upto 800fps from same setup. I have also checked barrel concentricity with laser & found it OK. Tank dump happens only when this oversized pellet is used. This pellet is also…Read more

Get better pellets.

You mean the quality of pellet is bad. I had same thoughtline but still wanted to take an opinion.

You mean

G – Ghost
I – In
R – Real
L – Life

The current set up is giving me 130…Read more

Dear,

At…Read more

Can you please tell us the difference between .177 & .22 spring & retainer?

Barrels are not sold in retail & imports…Read more

I fixed it for you though, so people can now see what you had originally written.

Thanks a lot dear.

Are you able to see the links & the message I wrote in mods/machinist section under heading “Spring Design Tool” ? I still can’t see anything there. I able to see all these messages I am typing in general section. Bit confused.

But as you can see my post that even my written message is also not visible. Any suggestions.

Their cheapest scope is $500. I’ll stick to a simple mil dot on an Elite 4200 if I was going to spend that much on a scope.

I was kidding. I just posted it as I came accross an advanced product.

Maybe a bit less ‘fat’ ? Its difficult to tell, no scale except your hand 😆

Oh yes it has become quite fat at 2″ ( 50mm ) thick. I am trying to trim it down without spoiling asthetics.

for me i woould off done the drill through right away as soon as the laminate,s had dried and then u could off mounted on the rifle to get the feel for it on there . it,s one…Read more

Here in India nothing that sort of thing is available off the shelf. Infact most of the people I spoke to are unaware about such a product. I have tried most of the dyes available in the market with pressure &…Read more

Hey how about this one. It is little different than your requirement but I thought it’s cool & hence posting it here.

Variable power, No focusing, preset zero at different ranges, Choice of reticle, range finder,…Read more

Thank you very much for your reply & attached image. I will try to put up such simlified images within next 2-3 days. It happend because I am not good at 3D programms & did the whole thing in coreldraw. Slowly I am trying to pickup with all you guys. Till then pls excuse me & keep guiding me.

I would also request you to post your…Read more

Resize them please

Ooooppppsssssssss I am very sorry. Now I have posted resized drawings.

Please see them.

Thanks

Karizman

All you senior members please see the drawings & suggest me if I am going in the right direction or not. It’s my very first attempt & want to keep the mistakes…Read more

did make a new valve and shoot now Baracuda’s with 50 fpe with a 17″barrel.

How will be the power with a 24″barrel, a bit more??

Thanks for response in advance.

Pic : valve without vent holes.

[/img]

Very nice looking valve. I am also working on an adaptor & being newbie I would highly appreciate if you can you show all…Read more

Thanks

Karizman

[/img]

[/img]

[/img]

[/img]

So… theres no difference between CO2 and Condor valve. The difference between the Condor and a Talon valve is bigger hole.

Thanks Yellow Ninja. Now I can go ahead with my first…Read more