Visit Talon Tunes
Updated on January 8, 2008
cygnus-x-d82
Participant
January 8, 2008 at 10:13 pm
Q:

drawing or picture of kickass bullpup lets see’em

ok my bullpup idea is moving forward….just spent all the cash found in the car as i got none after my mill purchase….found a nice piece of 3/4″x2′-4′ birch laminate…gonna glue 2 or 3 together for a nice thikness

but im missing a kickass design to go with…the more spacey the better

its gotta hide the trigger group i the back…and theres gotta be room for trigger linkage, im gonna do a little shield as well to protect the shooters ear in the unlikely event of a o-ring blowing out…but thats about all

Mods/Machinists

All Replies

Viewing 12 replies - 46 through 57 (of 57 total)

1 2 3 4
mr-lama
Participant
January 10, 2008 at 1:54 am

That blue one is a russian izh gun. It’s some kind of spring piston gun. Looks pretty neat.

Russians make the best weaponry.

blackwidowman
Participant
January 10, 2008 at 1:46 am

Very simple:

I made a pyramide shape sear and a rod drilled holes in both sear and trigger and attached a rod and made a stock. Over all 26″ in lenght.

I like the MP514 cant wait for it to be available in Canada

cygnus-x-d82
Participant
January 9, 2008 at 11:56 pm

i really like that blue one thanks i thinks thats what im going try and do

justforfun
Participant
January 9, 2008 at 10:35 pm

Not really sure what is meant by bullpup, this is short.

How about this one?

Roy S.

cygnus-x-d82
Participant
January 9, 2008 at 10:07 pm

this is pretty close to what i had in mind

except for the round part in the back

cygnus-x-d82
Participant
January 9, 2008 at 10:02 pm

Blackwidowman, that looks pretty cool, 2240 trigger thingy ? how did you do it….i play by ear…i mean assemble by ear….so im not quite sure how im gonna do the linkage yet

Jesx, i like the bottom ones steyer look…and that was pretty mych alond the line i had though of….allthough i would try make it more square’ish…im want that space look to it….the meaner the better….but still keeping the lines clean and simple….can allways go nuts with the dremmel once i got general idea

where do i find these russian bullpups…?

Thanks all for ideas and pictures !

shadoh
Participant
January 9, 2008 at 4:42 am

Look up some of those Russian onces Cyg. Those really look sweet. I think we have some pics on this sight somewhere.

jezx
Participant
January 9, 2008 at 3:50 am

i don’t know if this is kikass enough , but i’ll post , 50cal hpa and a .22 pump.

blackwidowman
Participant
January 9, 2008 at 1:40 am

My B51 bullpup:

Sorry a bit fuzzy


blodnob
Participant
January 8, 2008 at 11:58 pm

In bullpup body in mods n machinists.

cygnus-x-d82
Participant
January 8, 2008 at 11:38 pm

sounds cool…do you have any pictures ?

i should proably have mentioned it was for a B51…damn i m living my own little world assuming people know what the hell im mumbling about

blodnob
Participant
January 8, 2008 at 11:06 pm

Hey Cyg’ good to hear from you.
I managed to sort a fully enclosed breach for the same reasons you stated on the bullpup i started.. Breach n hammer slide inside a tube and the cocking nob is on the tube rather than the breach.A slot in the breach locates to a pin in the cocking tube with about 10mm travel.Then the tube seals up to an O ring on the face of the valve and also acts as a detent spring. Sorted the trigger unit out also.I got 5inch from the sear to the trigger blade is two stage fully adjustable for travels and pressures. I got to fit it into the trigger block now but it’ll have to wait due to other commitments.
Have fun and keep us informed. 😉

Viewing 12 replies - 46 through 57 (of 57 total)

1 2 3 4
  • You must be logged in to reply to this topic.

7 Comments