Talon SS Shroud

skybones

Participant

November 1, 2007 at 6:32 pm

I told you I didn’t have the b-lls to explain this!

bodhisdad

Participant

November 1, 2007 at 5:24 pm

Put the time and effort in researching the issue. Then drop $10-$20 dollars at the hardware store and you can achieve a quiet TSS, relatively. Mine was vastly improved over the stock empty frame. Hamer slap was the loudest thing heard. Or Get ahold Of Tony and your guaranted a quiet rig.

tom-kirkman

Participant

November 1, 2007 at 2:41 pm

On my Talon SS…

I dropped in a long lightweight coil spring, followed by nylon washers turned to perfectly fit the factory shround. The washers are spaced apart by O-rings, the first one by 4, the next by 3 the next by 1 and then one right next to the end cap. The end result is a gun that when fired sounds like someone snapping a twig. Not much more. From 100 feet away the neighbors don’t even notice. Cost me about $10 to do all this and took less than 20 minutes.

walkonking

Participant

October 30, 2007 at 5:40 pm

quote Yellow Ninja:

quote jooleyen:

Oh, I’m sure I will. When you’re baffling the gun, what parts of the gun do you disassemble to get the washers and baffles in?

http://talonairgun.com/forum/viewtopic.php?t=134 Anyone ever tried this? Looks very simple.

The end furthest away from you as you hold it in a normal shooting position has a small cap (has a hole in it for the pellet to exit). You undo a small set screw underneath the end of the frame to remove than, and that will expose the inside of the frame.. that is where you put the baffles and stuff.

How old are you? I think an adult should help you with this (preferably one that you know 😆 ).

Julien is a youth of 14 IIRC

synopsys

Participant

October 30, 2007 at 5:23 pm

quote shaky:

Synopsis:

How do you add a frame extender, while retaining the stock end cap??
I have a frame extender, albeit I had to send it back, but one has to remove the stock end cap and use its set screw to hold the frame extender in.

Thanks 😀

😀 I meant in other words ‘retained’ the cap in idea and but not actually using the stock end cap, the idea would be to use something like the end cap to divide the spaces…

y

Participant

October 30, 2007 at 5:08 am

quote jooleyen:

Oh, I’m sure I will. When you’re baffling the gun, what parts of the gun do you disassemble to get the washers and baffles in?

http://talonairgun.com/forum/viewtopic.php?t=134 Anyone ever tried this? Looks very simple.

The end furthest away from you as you hold it in a normal shooting position has a small cap (has a hole in it for the pellet to exit). You undo a small set screw underneath the end of the frame to remove than, and that will expose the inside of the frame.. that is where you put the baffles and stuff.

How old are you? I think an adult should help you with this (preferably one that you know 😆 ).

y

Participant

October 30, 2007 at 5:04 am

quote WalkonKing:

Some how Julien I get the feeling your going to accidentally kill yourself…lol

I think you might be right.

Maybe jooleyen should clear his internet history and cache immediatly prior to attempting anything with his gun once it arrives so we dont get blamed for any…. misadventure on his part.

shaky

Participant

October 30, 2007 at 4:39 am

Sorry man, I spelled your handle wrong!!!!!!!!

shaky

Participant

October 30, 2007 at 4:38 am

Synopsis:

How do you add a frame extender, while retaining the stock end cap??
I have a frame extender, albeit I had to send it back, but one has to remove the stock end cap and use its set screw to hold the frame extender in.

Thanks 😀

jooleyen

Participant

October 30, 2007 at 4:31 am

LOL. It’s hard to get a good close up image of all the parts of the gun. I haven’t seen one in person yet. I’m sure once I get it I’ll understand all the parts and it’ll all just “click” and I’ll be able to do these procedures.

Thanks for putting up with me – it’s not over yet. 😉

benfishin2day

Participant

October 30, 2007 at 4:08 am

I meant to say………..Without the help of the people here on the forum

oops………. 😉

benfishin2day

Participant

October 30, 2007 at 4:06 am

just take out the set screw at the end of the barrel (bottom of barrel) & pop the end cap off………it is just a hollow tube about 6″ long…….just remember if you can’t get the end cap off after removing the set screw then make sure gun is unloaded & point the barrel down about 2-3″ from some sort of cushion……..I dry fired mine into my foam in my gun case.

Of course I didn’t know to do that with the help from the wonderful people on this forum. 😀

walkonking

Participant

October 30, 2007 at 4:03 am

Some how Julien I get the feeling your going to accidentally kill yourself…lol

jooleyen

Participant

October 30, 2007 at 3:59 am

Oh, I’m sure I will. When you’re baffling the gun, what parts of the gun do you disassemble to get the washers and baffles in?

http://talonairgun.com/forum/viewtopic.php?t=134 Anyone ever tried this? Looks very simple.

benfishin2day

Participant

October 30, 2007 at 3:55 am

I must of done it wrong 😳

I’m going to have Mr. Tony make me a professional looking shroud……after speaking with him on the phone he seems like a very knowledgeable & honest man.

Is there anyway to quiet the hammer noise????

I’m new at this also.

But this is a wonderful forum & some excellent advice. I couldn’t figure out how to get my end cap off & after I buggered it up I decided to ask for help on this forum. I ended up blowing the cap off with dry firing….thanks to help I got from these guys.

I think you will like the Talon SS………..I love mine……….Plus its really “kewl” looking 8)

All Replies

5 Comments