Q:

EDgun Matador R3, caliber .30, single shot

Here is some information about new EDgun Matador, caliber .30.

1. Length — it became longer for about 50 mm. due to a new moderator (the same thing will be with the long one)
2. Weight — it became a little heavier due to the diameter of the barrel 14 mm instead of 12 as it was before, but not critically.
3. Moderator — new design, eccentric, diameter 38 mm, no thread on the case, just two O-rings.
4. Sound — VERY, VERY comfortable sound, to my opinion sounds quitter then .22, I can hear only the hammer.
5. Pellet — JSB .30 pellet, weight 2.90 grams (44 grain).
6. Speed of the pellet — with the standard regulator (set at 160 bar) — 270 m/sec (886 f/sec).
7. The energy for standard is 105 Joles (77.4 Ft-Lbf) .
8. Accuracy — about 20 mm (0.75 inch) at 50 meters (55 yards). Below you can see the shots to the bear can at 75 and 100 meters.
9. Barrel — made by Lothar Walther, especially for JSB .30, weight 2.9 grams (44 grain) according to my specification, choked, but very lightly.
10. Shot count for standard — 25 shots from 220 to 140 bar.
11. Volume of the reservoir — 270 cm3 (the after regulator space is bigger then at .22 and .25).
12. Length of the barrel for standard — 477 mm.

On October of 10th I went for hunting in the morning. EDgun Matador R3, standard, caliber .30, 44 grain JSB pellet, speed of the pellet 270 m/sec, one shot, distance about 50 meters. This bird:

Very tasty, by the way.

Here is the place where the pellet got in:

Here is the place where pellet went out:

No chances to survive for the bird such a size (about 6 kg.) A lot of blood on the ground. I am impressed…

At the same day I had 15 free minutes, bad mood and was in need to relax. Went for the nearest wood, took EDgun Matador R3, standard, .30 caliber. It was zeroed at 50 meters, the one I use this morning for hunting. I used Ballistic Calculator “Strelok”, made by Russian guy. I put a beer can at 75 meters and even didn’t tried to use paper to “zero” POI at this distance, just took out my IPhone, opened Strelok, changed to EDgun Matador .30, found that at 77 meters it will be second mildot from the cross and made 10 shots. Here is the result:

Then I made a picture of the can, put it vertical, moved back at 100 meters and shot another 5 shots. Here is the result:

There was a light wind from the right to left, about 2-3 m/sec, I didn’t made any calculations to the wind. Strelok told me that 100 meters will be half a mil down from the fourth mil dot at my scope. I put a fourth mildot to the top of the can and got all 5 shots down to the can.

I didn’t use any rests, tables or anything like that. I was sitting in my car, shot from the driver’s window. To my opinion not bad for such a position. The ballistic of the 44 grain JSB .30 pellets is equal to their other pellets so I don’t need to get used to new corrections by the mildot reticle.

I think I would change my Matador for hunting from .25 to .30 πŸ™‚

On October of 11th, just at 7:30 I got out home, took a car and went to woods. In 8:15 or something like that I saw a black grouse on the right side of the road. He saw me also, I stopped the car and watched him, taking R3 .30 ready to shoot, but as it was on the other side of the car I couldn’t shoot. The bird slowly moved to the bushes and directed to the thicket. I opened the door of the car, got out and moved back along the road taking the car between me and the bird. When I was about 50 meters out of the car, I took the right side of the road and moved to the place where I expected to find the bird, slowly. I reached the car, which was on the left on me and in few steps saw the silhouette in bushes, took the gun ready, but couldn’t see it in the scope through the branches. I was waiting about a minute or so, then the bird moved, I saw it in the scope through a lot of branched on bushes and shot. It moved quickly then fluttered for few second and that’s it. I loaded another pellet to the gun and moved closer to it. I found him dead.

I like this caliber as I doubt I could reach him with .22 through bushes. The pellet got in the very back side of him, penetrated through all his body and stuck somewhere near the neck. I was home at 9:30 after gutting it in the garage.

Today, on October 13th I decided to calculate how many shots will I have in standard Matador R3 in .30.

Here is the result.

Not bad, I think, 25 shots with average speed of 2.9 gram (44 grain) pellet at 270 m/sec (886 f/sec), from 220 bar to 140 bar. The average air consumption is 7.3 cm3 per one Jole of energy.

EdGun

All Replies

Viewing 15 replies - 76 through 90 (of 256 total)

1 2 3 5 6 7 16 17 18

ED Killed “Big Bird???” 😯 πŸ˜† πŸ˜€ Finally somebody killed that damed Big Bird! 😈

Thanks Ed! πŸ˜‰ πŸ˜€

KnifeMaker

Looks like a canon got him. Is that the standard? :4:

Another big bird today, distance 65 meters, dead instantly.

Here is incoming whole

Here is outcoming whole.

Ed

Just found out from Tony. November delivery is good. Who has nov 21st? That’s when Tony gets them….and we get our emails.

Maybe iΒ΄m talking about Nov. 13th 2014 ??

Me thinks that a tad closer than us. :3:

quote donnyfl:

I think it’s going to be my bet of Nov 25th that’s going to win it for me πŸ™‚

quote SECoda:

Since November 16th is the actual first delivery date your not too far off. I can feel that lap dance now. :11:

We may be just a wee bit optimistic. 😎

quote Sir Ville:

So my estimate Nov. 13th isnΒ΄t all too far off it seems. IΒ΄m good! Really good !!

I think it’s going to be my bet of Nov 25th that’s going to win it for me πŸ™‚

quote SECoda:

Since November 16th is the actual first delivery date your not too far off. I can feel that lap dance now. :11:

We may be just a wee bit optimistic. 😎

quote Sir Ville:

So my estimate Nov. 13th isnΒ΄t all too far off it seems. IΒ΄m good! Really good !!

Hi Ed

Do you plan on offering a multishot .30 cal in Morana? Also any plans on a heavier cal on the Morana?

Thanks

quote AKay:

Ed,

When might you be making a multishot version of the 30 cal?

AKay

Hope next year.

Ed,

When might you be making a multishot version of the 30 cal?

AKay

I have two enterprises, one in Europe (Estonia) and one in Russia. All the guns which are made (assembled) in Russia are sold ONLY in Russia. All the guns which are made (assembled) in Estonia are sold all over the world but Russia. I did it just to avoid to work with Russian authorities and custom.

Hacampbell;

my waiting is totally different story, i was waiting to find out the way how to bring the gun in the safe way, most of the shipping companies were rejected to ship the air rifles or any gun accessories to Iraq, my problem was the way how to import the gun to my city specifically, Eduard has tried with me with all his representatives, in Estonia, Kuwait, and some others i don’t remember, one time Mr. Martti has found a way via sea shipping to Iraq, but i was not sure about the way inside Iraq to my city,,,,,,,, and you know the rest……

Eduard is a great man and he was patient with me, he will not send you a bad gun, unless he should check everything then he will ship them, anyhow i believe one more month is enough to US guys to get the .30cal Matador by all of you……. i will send you my congrats before everyone to you all πŸ˜€ πŸ˜€ πŸ˜€ πŸ˜€ πŸ˜€ πŸ˜€ πŸ˜€ πŸ˜€ πŸ˜€ πŸ˜€ πŸ˜€ πŸ˜€

quote hacampbell1360:

Hemm waited more than 2 years, pretty much went to hell and came back to get it, anther month for me is ok. In the mean time, I will play with my other Edguns.

Since November 16th is the actual first delivery date your not too far off. I can feel that lap dance now. :11:

We may be just a wee bit optimistic. 😎

quote Sir Ville:

So my estimate Nov. 13th isnΒ΄t all too far off it seems. IΒ΄m good! Really good !!

So my estimate Nov. 13th isnΒ΄t all too far off it seems. IΒ΄m good! Really good !!

Thanks for the update Ed. I am very excited to hear everything is as planned, but am a little confused. The Edguns are assemble in Estonia first. Estonia is in Eastern Europe/ western Russia. These guns are for Europe market?

Ed said 20 (10 long and 10 short) are going to the US market. Where are these assembled? I don’t mean to whine, but just wants to have a clear understanding , that all

Hemm waited more than 2 years, pretty much went to hell and came back to get it, anther month for me is ok. In the mean time, I will play with my other Edguns.

Tony/Ed, are R3M breech and magazine update available for purchase ?

Thanks,

John.

Viewing 15 replies - 76 through 90 (of 256 total)

1 2 3 5 6 7 16 17 18
  • You must be logged in to reply to this topic.