NEW Vulcan videos!
Have more on the works
1.Vulcan fill valve gauge reassembly: https://youtu.be/4U3H1ICGKU4
2.Vulcan regulator—setting it without a pressure tester: https://youtu.be/5LLSVFbmHcs
3.Vulcan regulator how to set the output pressure: https://youtu.be/2TO6XkmRQOA
4.Vulcan regulator disassemble: https://youtu.be/-h1iQBzqFQo
5.Vulcan barrel removal: https://youtu.be/InguLiXv3jo
6.Vulcan regulator internals removal: https://youtu.be/X3MtER7sJNs
7.Vulcan air tube removal: https://youtu.be/qZnGic3BSkg
8.Vulcan .22 Hammer and spring removal delrine guide installation: https://youtu.be/gcV4E4Aq84M
9. Bleed screw oring mod: http://youtu.be/dAvWdbv9Fo0
10. air tube reassembly: https://youtu.be/rVcDmpeL9VE
11. barrel and air tube clamp reassembly: https://youtu.be/yPC38L3qn0s
12. trigger adjustment: https://youtu.be/BCryo_b1Tx8
13. cocking bolt tightening procedure: https://youtu.be/zlyqgCUxQcE
All Replies
I’ve been doing that for years, but over my shoulder using a mirror……………….. :4:
Lurker, where the hell have you been??
I gave up watching half way through…Does she ever try it with an airgun ❓
What a beautiful girl she is splitting card https://www.youtube.com/watch?v=KJsuihZaHyI
Hi Beach-gunner, on video is not mine spinner. I have one from my friend actually on that video. 🙂 But is not so good because red killzone is with weak material and bend it 🙁
For US guys is good spinner here http://www.steelplinkers.com/Quadrant.html
Some nice pictures are also here http://www.network54.com/Forum/451309/thread/1235155631/Woo+Hoo,+Quadrant+Spinner+Target+Arrived!!!+-+PICS
Octavius,
Where did you get that spinner target? I like the way you can make adjustments after your shot based on the reaction of the target. Where do i get one?
Beach-gunner :4:
Some video of vulcan .22 https://www.youtube.com/watch?v=ipuKCwkml3c
only on STATIC application—–> no movement—->don’t use on the piston rotor orings, the swelling affect of moly-55 my affect the movement of the rotor.
piston rotor orings? Where are these in a Vulcan?
Your right Zonk!
only on STATIC application—–> no movement—->don’t use on the piston rotor orings, the swelling affect of moly-55 my affect the movement of the rotor.
Benj Molly 55 for the o rings and dry silicone spray for springs bolt etc…
Jaime’s Tester doesn’t have a check valve inside the foster, so by bleeding the hose it will also bleed the air that’s keeping the reg shut—- when pressure drop below set point the reg spring will open and bump the regulated chamber. As for safety there should be a check valve installed—- if the foster Qconnect blows— you have a little rocket in your hands. Put it on a vice or install a check valve.
Ernesr, in your video on useing Jaime’s gauge to set the Cricket Regulator you show the REG’d chamber holds pressure when the supply air is bleed out. Should the Vulcan Regulator also hold it’s pressure ❓
Thanks. I sure wish Ernest would jump in and let us know what he uses for O-rings and which “dry” lube he uses for moving metal parts. Since he does a lot of tuning, whatever he uses must be good.
It’s Ernest’s video. He already has a link in this thread.
His safety info posted here in response to me is what was needed.
Let’s not “break the forum” again. 24 hours of dead quiet after the exchange! :suprisedn:
Dear Guykuo, please post the link to your video regarding Ernest safety issues!! Thanks
Regards
LarryW 🙄
- You must be logged in to reply to this topic.
My friends vulcan .22 55M/55Y https://www.youtube.com/watch?v=4RrXcEi0h4Y&nohtml5=False