NEW Vulcan videos!
Have more on the works
1.Vulcan fill valve gauge reassembly: https://youtu.be/4U3H1ICGKU4
2.Vulcan regulator—setting it without a pressure tester: https://youtu.be/5LLSVFbmHcs
3.Vulcan regulator how to set the output pressure: https://youtu.be/2TO6XkmRQOA
4.Vulcan regulator disassemble: https://youtu.be/-h1iQBzqFQo
5.Vulcan barrel removal: https://youtu.be/InguLiXv3jo
6.Vulcan regulator internals removal: https://youtu.be/X3MtER7sJNs
7.Vulcan air tube removal: https://youtu.be/qZnGic3BSkg
8.Vulcan .22 Hammer and spring removal delrine guide installation: https://youtu.be/gcV4E4Aq84M
9. Bleed screw oring mod: http://youtu.be/dAvWdbv9Fo0
10. air tube reassembly: https://youtu.be/rVcDmpeL9VE
11. barrel and air tube clamp reassembly: https://youtu.be/yPC38L3qn0s
12. trigger adjustment: https://youtu.be/BCryo_b1Tx8
13. cocking bolt tightening procedure: https://youtu.be/zlyqgCUxQcE
All Replies
I haven’t shot the Vulcan on paper through out the fill range for POI shifting. so I cant say!
well that spacer isnt making any noise without the oring mod.
overall the shot cycle sounded solid. next one will cut more milling slots to increase air space.
Ernest, why Vulcan does not suffer from POI shift because of AT pressure changes? It has a pretty similar design to Cricket.
Bump
Did the machining of the spacer do anything for the ping? I noticed also that you did not add any tape to it. How is this working?
And to add, what is the grease that you use for lubing like for when you slide the reg back in place? Is it just 100% silicone?
Did the machining of the spacer do anything for the ping? I noticed also that you did not add any tape to it. How is this working?
:8: :8: you go Ernest, you go! 😀 !
Vulcan Barrel and air tube reassembly:
Very nice Ernest. Good idea on beveling the fill probe hole, that should save wear and tear on the fill probe O-rings.
Sent from my Z30 using Tapatalk
The Vulcan and mutant use the same size, but the cricket is a step down in size.
thx ernest,
4 the ball check on the bleed screw video!
very helpful & merry Christmas to u & your family!
Merry Christmas
Ernest what is the thread size and screw length. I have nylon tipped set screws for my cricket. Might just get them instead if they are available. Think Mc master Carr
Sent from my Z30 using Tapatalk
Here’s a video to add an oring under the ball check on the bleed screw and air tube reassembly!
1.The ball keeps the oring centered while compressing the oring–after a lot of testing its best to lightly seat the ball metal to metal then the oring will do the rest.
Air tube reassembly: https://youtu.be/rVcDmpeL9VE
WOW, Earnest this is awesome information, and I appreciate your posting them to educate us. My 25 Vulcan is my one and only PCP and even though your vids are very informative I still would like to send to you for a professional tune. Would you please PM me the cost and a timeline for completion from when you receive my Vulcan? Thanks a bunch and Merry Christmas! :4: :4:
can some one please post some info on the,
0-ring under the bleed screw.
i know its here some where but i can’t find it . :rofl:
- You must be logged in to reply to this topic.
More Videos:
Trigger adjustment: https://youtu.be/BCryo_b1Tx8
cocking bolt—hole under the oring to jam tighten to prevent it from backing out. https://youtu.be/zlyqgCUxQcE